3d printed magsafe stand

If you want to use Anet's original M5 screws/t-nuts, just print the parts with 100% infill and drill out the mounting holes with 5.0 or better yet, 5.5mm (to give you some alignment room) drill. Edit: Full screw list, as requested: * 10pcs of 412...

Mount the printed heatblock with the front and back parts of the mold, fix the whole with 2 screws. Make sure it's tight enough. (pictures 7 and 8) 2. Put the freshly assembled block over the bottom part of the mold (picture 9). Make sure the holes...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

compatibility note: for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like...

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

First, you'll need a 2 gallon bucket (I got one from Home Depot for a few bucks), some M5 screws and some M5 knurled brass threaded inserts (use a soldering iron to install in plastic).I also included a strap mount so I didn't have to carry the ICM...

compatibility note: for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like...

All parts are printed, including hinge pins. I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to...

The major innovation in coins the Byzantine’s made was to have the emperor face the front rather than print a profile. Most US coins would then adapt the side profile and bank notes adapt a front facing image, if not cocked to the side just slightly....

This collection is a curated list for the Gridfinity system that includes Structural prints and common applications. The collection excludes any designs for unique tools or vanity items. ...Please like/favorite the original posts</p><p>If you are...

Use the backlash option to allow for the gears to work with printing inaccuracies. Bevel gears are more complicated. Meshing bevel gears have the same cone distance, circular pitch and pressure angle. The cone distance, circular pitch and number of...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

These models should be also shrank to 80% scale when printing.If "1min-holder-1.stl" is too thin, use "1min-holder-1-thicker.stl" instead.note : Since the number of optional files increase, it might be now confusing to add them here. So please...

Just put the LEDs and alarm speaker in a box with a labeled side (printed in white filament) and attach it to power supply fan connector... there is even a slot in my power supply cover to allow the wire to be slipped into (and out of) the power...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

You can set the X_MIN_POS to -1 and the Y_MIN_POS to -24 and the bed size to &nbsp;234 on X and 211 on Y and then you won't run into issues with it trying to print off the edge of the build plate, you should also change them in the slicer to match. I...

The parts are small so I printed with 100% infill and also used supports for the hex nut holes and the two points that extend out the side of the inside block. Before applying silicone wipe the mould down with dish soap which acts as a separating...

Once I print some more of this I will keep tweaking it - and look to finish meshing a magazine. Nov 29, 2019 Part 2 - YEEUH. HUGE update! I've found a way around a lot of the hard stops of the limitations of space and dimensions, but still...

Make sure to print the models with minimal infill, - they do need to float after all. There are two main pieces in the kit which we add magnets to: the IgG (antibody) and the Ag (antigen) models and it is*really* important that we insert the magnets...

You might want to widen the holes for the screws with a drill (depending on the printing quality you select). 3. Before assembling anything to the case, use a blow torch to warm up the screw brackets and screw in the screws to gently form a thread...

... ends at the posts) 8.) To mount it match drill using the fitting into the side of the psu and run two machine screws with a nut. (Bonus points if you use Loctite or a lock nut on the nut.) Print Settings Rafts: No Supports: No Category: Electronics

Megacity Desert Habitat building for tabletop, expanded by rectangular build option.It contains:WallsRoof tiles with the capssome special sized doorssome basic bits for decorationYou may need to mirror the corner pieces in your slicer to get all...

# Warning **PLEASE PRINT OFF THE SHROUD AND MOCKUP 4010 BLOWER AND CONFIRM FITMENT BEFORE PURCHASING OR MODIFYING ANYTHING! PLEASE POST IN THE COMMENTS IF THIS SHROUD WORKS FOR YOU AND WHAT CARD YOU HAVE INSTALLED** The shroud is designed to sit...

The filament used is all dark red PETG eSUN brand, printed at 245 ° with bed 80 °, 100% infill to avoid any deformation in the heat. The description is not detailed simply because it is not complicated as a project, certainly a bit of manual...

This design fits on a Prusa i3 MK3 bed.Note: Please only attempt this if you already have some experience with soldering, wiring and electronics in general.Note: Some ATX PSU's may be too deep for this design so if your PSU is over 135mm deep it may...

I used black to match the container) Magnets (8 total): https://www.kjmagnetics.com/proddetail.asp?prod=DC6PC-BLK Mesh: https://www.amazon.com/gp/product/B07563327H/ref=ppx_yo_dt_b_asin_title_o04 o00_s00?ie=UT F8&psc=1 Thermal Adhesive:...

I don't remember what size o-rings were used, but print the piston so that it just fits inside the 1-1/4 PVC tube and try different sizes until they make a decent seal. It doesn't need to be tight. I also sealed up three of the pass-through ports...

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...