3d printed magsafe stand

I make this remix to fit my aukey magsafe adapter to this print.

This is a stand for iPhones having the Magsafe loading capability (iPhone >=12). I use it with an iPhone 13 mini, but it should fit larger models as well. The phone can also be placed in a 90-degree angle on the stand. I optimized the stand to...

... on a desk or wall. Note that this is not compatible with the original Apple MagSafe charger as its dimensions are different. [Download STL and Source files](https://www.printables.com/model/268363-ravpower-magsafe-15w-wireless-charger-base-stand)

Magsafe charger stand for iOS17 standby mode with Apple Watch charger. Older AW charger wires fit through too. I used 30% cubic infill and 0.2 layer. ...Tree support and the print time with default settings in Cura was something like 10 hours.

Printed 0.2mm layers without supports on Ender 3 pro The stand is hollow allowing you to coil excess cable inside as well as push out the charger. ... The Baseus charger version requires double-sided adhesive to stick the magsafe charger to the holder.

Voronoi styled 3d printed latop stand.

Phone stand which is placed in BMW cup holder to support a Apple MagSafe charger. Cable Management included. ...Tested on BMW F10/F11.

https://www.thingiverse.com/thing:4758057 Just a remix of prezmc's iPhone 12 Pro MagSafe stand. https://www.thingiverse.com/thing:4649719 This one has been made a little bigger to suit the iPhone 12 Pro Max w/ a case. ... I have also added cable...

magsafe charging stand for iphone 12 & 13 mini. ... you just put the charger in the hole. magsafe_stand_v8 is the newer version and is bit higher if you also want to be able to use cable charging. ...glue is recommended.

This is a stand for the original Apple „MagSafe Charger“ (required). It is intended as a convenient desk stand (60° angle). For both the shell part as well as the insert part use supports (STL is not oriented for printing and the two parts need to be...

By not locking the magsafe to the stand, the advantage is you can take the phone off the stand and keep charging. Works in portrait and landscape orientation. ... If there is interest in this model I can make verisons for other iPhone sizes and case...

This a a stand for the iPhone 12 Series with MagSafe, Put the charger in and run the cable from behind or from below if you want to drill a hole in your desk to hide the cable completly.

This is a stand to hold both the Apple MagSafe charger and Apple Watch charger. It is sized to work on all the current models. ...Devices snap in and are held securely.

iPhone 12 Magsafe Wireless Charging stand. Pretty simple design for the Apple Wireless Charging puck. Just pull the cable through and smash the puck into place. ... Pretty well balanced and doesn't flop over when attaching/detaching your phone.

This attaches the stem from the source thing (Adjustable MagSafe Stand by NoahColly) to a cup so that you can use this in your car as a cup holder magsafe stand. You will need several other stl files from the original source thing to complete the...

This is a Remix of the "iPhone and Apple Watch charging stand by samesser" I redesigned the Stand for my MagSafe Puck and Apple's Metal Watch Puck. - The Charging Stand has now a smaller Footprint. - Cable Guide for Apple Watch is narrower (4.75...

## Horizontal Magsafe and AppleWatch Stand This is a combined MagSafe iPhone and AppleWatch charging Stand that holds the phone horizontally to take advantage of the new StandBy mode in iOS 17. All cable cutouts fit both USB-A and USB-C cables and...

Works great as a desk stand use as well as for your night stand to use the iPhone in the StandBy mode.Print and Setup instructionsPrinted using Overture3D PLA PRO filament. Layer height: 0.2mmInfill:  15% (or) more if you want it to have more...

Hinged / multi-angle update to @Thomas_50404's Magsafe Charger StandI added a pseudo-ball-and-socket joint / hinge to the arm of the stand that allows users to tilt their phone 25 degrees back and forth while charging.The hinge pieces are printed...

A remix of the iPhone and Apple Watch Charging Stand. I added a shelf so that it could support a watch with a heavy band. ...I also edited the area behind the MagSafe to allow a USB-A cable to fit through.

This is a remix of the original Weighted Ball MagSafe Charger Stand (4783199) by jburd which is a fantastic stand but didn't accomodate the iPhone Pro Max very well (especially with its case on). This remix just increases the height of the Weight...

I also referred to a couple of online designs for the screw-retention holding section for the magsafe puck.Printed in PLA with 0.2 layer height 30% infill, with support enforcers, and modifiers to make the lower section heavier (higher infill at...

A MagSafe charging phone stand designed for use with a Google Pixel 8 Pro and Google Pixel Watch 2.Please note! The watch charger is sized for the PW2 watch. ...If you have a PW1 you'll need to modify the code to make the opening larger.

I also wanted the magsafe to be easily removeable from the stand so that I can use the phone while the magsafe is connected to the phone. This stand works with the iPhone 12 with a case and an Apple Magsafe charger. I suspect it will work with an...

This model remixed from Thingiverse - Digital Designs for Physical Objects - Thingiverse here.I have an airpods pro which not compatible magsafe(no magnet version).So I modified the stand side for adjustable ange mount.It use m3 bolts and nuts, mount...

Slide the magsafe puck into the first piece, then line it up and lock it into place with the stand half. While not required, it is recommended that you stick some thin felt or rubber pads onto the top half so that the phone actually sticks to the...

... fit phones/cases with bigger camera lenses and protection. Can use phone landscape or portrait.I'm new to 3D design and Fusion 360, so all feedback welcome.Charger in picture is an Amazon purchase (not Apple). ... Made for 56mm diameter charger.

A 3D-printable stand for smart phones.

It also has the added feature of the MagSafe puck being easily removable from the stand, in case you need to use your phone while it is charging. There is a Solidworks parametric file attached which allows you to customize the design for any...

I could not have made this happen without help from:I used this file to obtain the Gridfinity stand compatibility:https://www.printables.com/model/567797/filesI used this file for the Logo:https://www.thingiverse.com/thing:1402622and the head piece I...