3d printed magsafe stand

Before you wasting over an hour to test print the actual stand, you can print the much smaller file "Mag-Safe Charger Stand FIT TEST RING" to make sure you have a snag fit with the charger first. There are 2 versions included. One is tilted 32...

Slim MagSafe charger stand for good heat dissipation. Also has little shelf for wireless AirPods charcing.</p><p>Needs mounting on surface so there are two versions one with adhesive tape recess in bottom part and one version with screw hole and tape...

Easy to print iPhone stand that takes advantage of IOS 17 Standby Mode using your official 15W Magsafe wireless charger. Charger will fit without friction. Used 2 very small pieces of black electric tape about 1/2 inch long on opposite sides of...

My design for a stand that holds both the Apple iPhone MagSafe and Apple Watch wireless chargers so you can view and charge both devices at the same time. ...It holds both chargers flush with the front face of the stand and features a groove to route...

I got a magsafe compatible phone case for my pixel phone and ordered some magsafe chargers on amazon that didn't fit stands that I had already so I designed one to fit the new charging pucks. ...The stand fits both a Pixel 8 pro and works with iPhone 15...

This was the second iteration of my MagSafe Duo Charger Stand for iPhone & Apple Watch. Unfortunately I did not account for the weight of the phone itself in my design. ...So the stand will topple over unless an apple watch is placed on first, the stand...

A simplistic 3D printed vertical stand for DR ZABER Sentry 2.0

I modeled a phone stand in Fusion 360 (file attached) to hold the iPhone 12/12 pro with a MagSafe charger. It also holds the Apple Watch charger with a little grove in the back to hold the watch charging cable. I used PETG because that's what was...

DonSonsi made a very excellent MagSafe stand for the iPhone (12, 11, X, 8) and Apple Watch. Thanks! This Remix adds a speaker amplifier shelf to add a little better sound output while supporting phones with cases better, as well as an iPhone-only...

I designed this stand to hold my iPhone 12 while it was charging on the magsafe compatible wireless charging disc. It has been tested with both iPhone 12 and a Samsung Galaxy device. ... The recess has a little bit of wiggle room to allow you to move...

... and 2 wall for most of the print. For the section between the phone and watch I printed at 50% infill and 4 walls for better strength and less chance of cracking the print when removing supports (I found out the hard way). Category: 3D Printing

Simple magsafe stand for my iPhone 12 Mini designed to be clamped to the edge of a table or shelf. I wanted a stand fixed to the shelf, so I can grab the phone with one hand, so I made this one, which I can attach with an old clamp from a lamp. ...

... ...No supports needed during printing.I printed with:material: PLAnozzle: 0.4 mmlayer height: 0.24 mm (first layer: 0.28 mm)perimeters: 3infil: 10% CubicThe AirPods holder part has a hole for an M3x10 hexagon screw to prevent the plug from falling out.

Redesigned the Upper Part to take a Heyday MagSafe Charging Puckhttps://www.target.com/p/heyday-8482-magsafe-charging-pPrint the original base from:https://www.printables.com/model/46451-iphone-12-magsafe-docking

Of course, you could minimise them by reducing the layer height.Printing RecommendationsThe stand should be printed with overall supports enabled which will yield tiny supports at the cable openings and also some supports for both top area charger...

I admired 1997CamaroZ28's ingenious creation of a stand for ericthepoolboy's exceptional model of a Camaro LS3 V8. ...This is a straightforward iteration of the original stand design with some logos incorporated into the 3D printed elements.

Added middle section parts TopMid, MidMid, BottomMid to be able to extend the "Korg Volca Stand 3x - Pure 3D Printed" by Fusksalad to 6 or more Volcas.

ESR Wireless Charger with MagSafe Desk Mount / Stand © 2023 by Tyson Laevens is licensed under Attribution-NonCommercial-NoDerivatives 4.0 International If you'd like to sell it commercially, please reach out to me in the comments. ...We'll get in touch...

stand for storing 3d printed RC car PV3S against wear of leaf springs height 85mmstojan na uložení 3d tisknuteho rc auta PV3S proti opotřebení listových per výšky 85mm

... I also added a spot at the bottom to hold the Airpod Pros. It works with an Apple MagSafe silicone case and without a case. It also works sideways.&nbsp;Pictures depict test print printed at 0.25mm Draft, with support on bed, brim, and 10% infill.

... fellow tech enthusiast, they requested a customization - a holder for their phone's charger as well. ...Accepting the gauntlet, I set out to create something innovative and here it is: a 3D-printed iPhone stand that also charges your device on the go.

This is a remix of https://www.thingiverse.com/thing:4657117 I realized that the original design would not accommodate the new iPhone 13 Pro, as the new camera protrudes too much to allow for the MagSafe to dock. So I created a little slot to...

... Printed with 25% infill and 2 wall for most of the print. For the section between the phone and watch I printed at 50% infill and 4 walls for better strength and less chance of cracking the print when removing supports (I found out the hard way).

iOS17 has a StandBy setting, aka “Nightstand Mode”, where a different display is shown when the iPhone is attached to the MagSafe charger and is in landscape orientation. This stand was designed around this new mode and also adds an Apple Watch...

I absolutely fell in love with 1997CamaroZ28's 3D Printed engine stand for Ericthepoolboy's LS3. Inspired by a branded remix of that, I designed one with some Mazda branding - both modern and retro logos. ... The pieces are fully interchangeable with...

If 3D printed, this stand cannot mount a running engine as the plastic will melt. Designed in onshape by myself. Update: I have added a "V3" model (it is not pictured as i have not printed one myself yet) with some tweaks and additions for...

This is a remix of NoahColly's iPhone 12 Pro Max Magsafe Stand. I wanted something that would work with my iPhone12 Pro, and with a cheaper Qi charger. Specifically, it's designed to perfectly fit a Yootech Magnetic Wireless Charger, which works...

I required a laptop stand for my CNC machine, so I came up with this adjustable design that utilizes only common hardware store components and three 3D printed parts, all of which can be acquired for under $20. To assemble this project, you will...

This stand is made for holding the Apple Mag Safe Charger.The stand is 3D printed in the orientation it would be placed on the nightstand, with support structures enabled throughout. The recommended print settings include a layer height of 0.10mm for...

Another mobile phone stand for large format mobile phones. ... For details about design and printing, please see my youtube video https://youtu.be/r16oTriTprw .