3d printed labo

Welcome to the home for the things to print for the Eff-Uno Racer project (https://github.com/oracle-devrel/eff-uno-racer). Eff-Uno Racer is a LEGO© Open Wheel Race Car that you can build and remotely control. Most of it is made with LEGO© bricks...

for parts look at the parts list PDF that can be found in the FGC-68 starter kit to actually see how to do it whats this link.https://youtu.be/M_1AAlgVm-4 some tips disassemble the FGC68https://www.youtube.com/watch?v=pDRv5jwRReA a introduction to...

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

The measurement is relative to the height it extends above the surface of the badge.[background color] and [foreground color]These dropdown boxes change the colour of the badge background and the contrast colour which effects the border , logo and...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

Alternatively, one could print the breasts and make an elastic mold. Step 1 If you look at the breast from the front and imagine a ball in the breast; what diameter would the ball be? <b>Bd= x (mm)</b> If you look at the doll's chest from...

...There is a preview .stl--nothing to print yet! Updated with v2 parts 09/21/2017: Added longer V2 parts that use two screws for better clamp support, similar to a woodworkers clamp. If you are shooting for light and cheap stick with the V1 clamps.

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

and post some makes if you use these it lets me know I'm not wasting my time uploading my designs and if you like what you see check out more of my lures at https://www.theneverendingprojectslist.com/ Print Settings Printer Brand: MakerGear Printer: ...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

Access it here: [http://www.thingiverse.com/apps/customizer/run?thing_id=287025](http://www.thingiverse.com/apps/customizer/run?thing_id=287025) To print this design, set the following options: - grid size: 0.1 - orientation: 1 - pixel shape: 4 -...

Best printed with PETG at 100% infill. The larger version (stl and 3mf included) are specifically sized for the newer style pumps that use the clip on nylon base. They will work with the screw on style metal base. Usage of the mold/die remains...

It's a SCAD file, so it's pretty easy to modify (add/change axis button layout).\nNote: The joystick holes look like they won't be holes, I assure you they will be when they're printed.\nParts:1x Adafruit Feather 32u4 Bluefruit LE1x LiPo Battery1x...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

The equipment tray and servo lock **must be printed as one assembly**. I separated them so you easily could make servo lock for different servo (in that case I use 1181MG servo). I made the square on the equipment tray floor for you to easy pairing...

Mount the printed heatblock with the front and back parts of the mold, fix the whole with 2 screws. Make sure it's tight enough. (pictures 7 and 8) 2. Put the freshly assembled block over the bottom part of the mold (picture 9). Make sure the holes...

Please ensure that this part will fit before printing. May require some tweaking. Results will vary.) ~4 In. flap ~Flap joint Optional parts: ~4 In. coupler Things you will need to purchase: ~4 In. duct fan...

The previous versions tot more than 2.000 throws.Results: the side 6 has almost 33% of chance to been getting (instead of 16,7% for a balanced die), the sides 2, 3, 4, 5 have between 15% and 18% of chance to been getting (some variations are...

####Broom stick section: First test the printing tolerances by assembling only the left, right and release part. Insert the clippart of the wheel section. You might have to grind/cut a little bit on the parts for a smooth fit. Push in the Insert...

The "printmode = true" with its following variables will prepare a print-ready layout of your parametered Structures. The length of each (not printable) Threaded-Rod will be "echoed" in the OpenSCAD-Console. They can be cut to exact that length. -...

... ends at the posts) 8.) To mount it match drill using the fitting into the side of the psu and run two machine screws with a nut. (Bonus points if you use Loctite or a lock nut on the nut.) Print Settings Rafts: No Supports: No Category: Electronics

Print Settings ==================== Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm ###Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and...

Once you have the wires soldered and a battery in place save your game again remove the cartridge and slide the cover into place. A great tutorial on replacing GB batteries while keeping your save can be found here....

The interior is covered with heat-reflecting material to avoid heat loss and also to slightly amplify the internal lighting given by a simple LED lamp with an external switch.The filament used is all dark red PETG eSUN brand, printed at 245 ° with...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side...

First, you'll need a 2 gallon bucket (I got one from Home Depot for a few bucks), some M5 screws and some M5 knurled brass threaded inserts (use a soldering iron to install in plastic).I also included a strap mount so I didn't have to carry the ICM...

print each part. arm2.stl and c270_lens_adaptor_0.6875inch.stl need support.2. Disassemble the Logitech C270 and remove the PCB. Refer to ‘How to remove the PCB’ for how to remove it. 3. Attach the PCB to the c270_pcb_case.stl. The screws used for...

I printed in PETG, Black, Orange, White. Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held...