3d printed ice breaker

The interior is covered with heat-reflecting material to avoid heat loss and also to slightly amplify the internal lighting given by a simple LED lamp with an external switch.The filament used is all dark red PETG eSUN brand, printed at 245 ° with...

There is a version (1c_p1.stl and 1c_p2.stl) that is cut for easyier printing on FDM Printers and a Version (1c.stl) that isnt cut. 2: Its Basically a hinge in Sector mechanicus Style that allows you to make ramps or drawbridges. It comes in 3...

These go in the 3mm perspex (or printed panels) (key spots marked in yellow). 24-42 x 10mm M3 countersunk screws. 5 x 10x5x4 bearings (easily available in hobby/printer shops). 10 x M6-PC4 bowden connectors. 12 x M5 nuts and bolts to mount to the...

Printing Tips: 30% infill at 50 mm/s If you wish to design your own fraction piece, you’ll need to know the size of a whole. One whole piece is 50mm tall with a diameter of 50mm and an inner diameter of 12.5mm. ...With those measurements, you should be...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

I figured if I ever had a print that needed that additional ~5mm of build volume, then I will deal with new lead screws then. I also already have an Ender 5 Pro with a Dual-Z XL upgrade for a whopping 500mm Z build height, (but still only a 220mm X/Y...

This is a ventilation system for an IKEA Lack enclosure.The top and bottom flanges have a “key” that will align the two halves so that the screw holes line up as well as the notch that can be used for servo and/or fan cable management if you wish to...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

This gives me enough string that when I loosen the ligature I can easily get the reed on the mouthpiece, and when I tighten the mouthpiece I get as much tension as I could possibly want. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts:...

Jam jar, "Bonne Maman", strawberry :-), 77.60 mm outer diameter Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations under the same username (rolfmobil)... Print...

This version is a modern lamp. A Halloween version and other versions will follow. Print instructionsDisclaimer This lamp requires the skill to work with mains voltage (230V/110V). If in doubt, ask a professional (or your parents if you are underage)...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

The parts are small so I printed with 100% infill and also used supports for the hex nut holes and the two points that extend out the side of the inside block. Before applying silicone wipe the mould down with dish soap which acts as a separating...

It is very important that there are no gaps between the screw and the walls of the tube, so if the screw is rubbed it should be so, it will quickly get used to the walls for this if the printer prints in plus, there are screws in minus. The back...

The alternative file is what is in some of my first renders and does look cool, but they are often annoying to print and glue on the vehicle so adding them is up to you. Size of model when completed 165mm length, 90mm width, 68mm high. ...Instructions...

If you'd like to buy a print of this with metal inserts in the drill holes, please check out my gunbroker page: https://www.gunbroker.com/item/858377600 This is version 1.2 of the C93 paddle release jig I previously released. This updated version...

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

Note: This will decrease your print height slightly! The CR-10S Pro struggles even more than the CR-10 series when it comes to Z motors going out of sync on power off. This is due to the same design as the one used by hoegee, but it works perfectly...

Then print the 2 models and install them on the printer. For the sensor set it in retract mode and touch the nozzle and the bed. Then place the 2 mm (approx.) allen wrench supplied with the printer between the tip of the sensor and the bed and screw...

Printed in transparent PLA. Part numbers it goes by: 00653521, 653521, 8713411212741, 7439647988922. ... According to internet the same shade works for: BOSCH DWA06W450B/04 DWA06W450B04 BOSCH DWA07W450B/01 DWA07W450B01 BOSCH DWA07W450B/02...

このモデルは以下のモデルの自己Remixとなっています。 CE32A 1" Speaker Driver Enclosure PAM8403-based Tiny Audio Amplifier Board Adafruit Stereo 3.7W Class D Audio Amplifier MAX98306 Enclosure Adafruit Breadboard Friendly 3.5mm Stereo Headphone Jack Enclosure Adafruit USB...

Print instructionsPrinted with PLA plastic at 200 micron and around 7% fill. Mount the two front arms to the main body with a single zip tie. These zip ties should be quite snug, I used pliers. For the rear arm/pivot, first give the hinge slots a...

Megacity Desert Habitat building for tabletop, expanded by rectangular build option.It contains:WallsRoof tiles with the capssome special sized doorssome basic bits for decorationYou may need to mirror the corner pieces in your slicer to get all...

Case for Atari 1050 / XF551 floppy power supply unit. Krabička pro napájecí zdroj disketové jednotky Atari 1050 / XF551. Print instructionsenglish text bellow ==== CZ ============ Napájecí zdroj pro floppy Atari 1050 / XF551 Jde o návrh napájecího...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

The main container and the insert are the same for all heroes, so 7 identical main containers and inserts must be printed. The lid is decorated with hero relief. There are 7 heroes in the game and there are 7 different lids dedicated for each one of...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...