3d printed gopro case

I have modified this with an easier to print screw ring with nubs for easy grasping and have uploaded 2 versions of the screw ring and insert one is scaled down to 99% so if the full size one is too tight the scaled down version should fit easier. I...

I encourage experimenting with springs and print settings if you know what you're doing to create a blaster fine-tuned to your needs. Grab your Snakethanhas here: https://www.thingiverse.com/thing:3890229 Feedback is very welcome, and though I...

I printed these parts using a delta-style printer, employing the following settings: For the Rings & Handle: - Layer height: 0.2mm - Outside perimeters: 2 - Top and bottom solid layers: 3 - Infill density: 20% full Honeycomb For the Clamps: - Layer...

The motor plate/gearbox must be printed with supports. A 3mf file is provided with suggested plating and support enforcement block specifications. Supports should only be specified for the gearbox portion up to the second bearing. Removing support...

... shape con the center of the top side). I have only checked the grids with TT685 since I do not have the others. I would be very grateful if you could publish your photos made with this grids. Do not share the model files nor sell printed grids.

  My will at first was to provide to the community affordable and easy to print by yourselves nameplates for the games who require generic tagging : Bloodbowl, Warcry, Warhammer Quest... And to help some makers adding a personal touch to their...

... I have not mounted the printer, controller, and power supply on a base board, so the wires to the controller are not cut to length. It's still pretty messy, but I'll do it once I'm happy with the design and fix everything down. Happy printing.

If you're using a servo, you'll also need to print the rev counter (“rev_counter.stl”) and install an extra magnet and an additional reed sensor. On the other hand, if you opt for a stepper, you'll only require an extra coupler. For convenience's...

If they break reprint your model and try again or just glue it in place Reassemble you should be good at this point (unless you didn't test it along the way) Post-Printing This is my video on how to assemble the kit and the mod, it's also a video...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. Die...

The design consists of 3 parts : 1) the base (about 4 hours) - 12% density zig zag support and 10% gyroid infill 2) the spindle (about 4 hours) 3) the screw (about 20 minutes) Note : spindle has been printed with different support angle. The outer...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Agannon,...

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

... were destroyed after the war to comply with the alliance treaty obligations. The end. Print Settings Printer Brand: Anycubic Printer: Photon Rafts: Yes Supports: Yes Resolution: 0.02 Infill: n/a Filament: anycubic resin green Category: Model Robots

... on confirming its fit for a Focus ST. If you'd like to help confirm, print out the drawings and let me know whether or not it fits! ... Thanks Special thanks to Reddit's u/poco153 for providing True Value part numbers; check Poco's build out.

The rods should be cut to length (about 86mm, give or take, size them up against the holder once it is printed). I'd recommend cutting them so that they have about 1mm to 2mm play side to side once installed; if cut too snugly they can extend past...

eerything you need to play is included, it's an easy print for a game that you will play for days and days!!! hope you enjoy it!! Rules: in french sorry... (you can copy and translate!) Material list - 1 game box/stand - 1 game board - 4...

Besides printed parts, you'll need to complete these hardware requirements: Lid: (Button Head Screws ONLY) Six M3 6mm or 8mm Button Head Screws Eight M4 8mm Button Head Screws Inside Box: All Boards: M3 4mm Button or Cap Head Screws Fans:...

The entire box is designed such that if you print with 6 shells in your setting the outside walls will be solid, and the front wall will be double thick as it will take most of the hits. The bottom is flat, but has a large recess to allow you...

I printed the coupling with TPU and fits onto the gear wheel of the stepper motor and onto the self-locking nut M8. The stepper motor probably comes from a Canon inkjet printer. ... Are needed: 1x stepper motor 35 mm SMJ35-4831-B or identical 3x...

So I can't really suggest someone to print this and build it, it will be hard. /thats why I'm not sharing .stl files you mght need to change somethings) You need to know some Python and Arduino code to figure it out and get it to run. If you don't...

nut_diameter assigned value 12 matching prior statement concerning fastener dimensions now directly correlated related head type specification which dictates form interface compatibility required operating tools attaching part assembly process;...

Comes in 32mm and 75mm Scale - PreSupported option available (Actual printed size is 65mm and 150mm respectively).   An elite fighting duo that are legendary amongst the front line and special operatives of The Golden Griffins. Just the sight of...

we should be able to read the block now success = nfc.mifareclassic_ReadDataBlock(currentblock, data); if (!success) { PLAY_ERROR; return; } // Read successful for(int i=0;data[i]>0;i++) { if(data[i]=='') { Keyboard.press(KEY_LEFT_SHIFT);...

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

So here we are about three months later with something that, after quite a bit of brainstorming, parts printing, carbon cutouts, messes and success stories, looks ready to be shared with the community. And now, it's over? Well not...

Here's a list of things you'll need for the project: To start, print out this box I designed! Here are the project materials. These aren't specifically for this project; they're all items I had lying around from other projects. You can find them on...

I used these: https://www.amazon.com/gp/product/B07H97G7NYCyanoacrylate glue ("superglue")1 ring terminals with > 9.5mm ID ("yellow").Some wireOptional: hacksaw and/or file, and pliersAgain, double that if you're making two coil...

This housing is **printfriendly** means it is easy to print and needs no support For the powersupply i used this components: Bush 5.5mm x 2.1mm: [Link]https://www.amazon.de/gp/product/B019IFAQ5G/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1...

It is though that below the ice in the surface it is a liquid water ocean, and it was early speculated that this ocean could hold life, with the geotermal heating from the tidal interactions with Jupiter and the other Galilean Moons (Io, Ganymede and...