3d printed frostmourne

For example, I always made the print bed side visible because I liked the surface better there. With this little Stepdown Modules you can connect the 12V fans to the 24V power supply. If you have installed these two Noctua you only have to remove the...

If you don't use your Western Digital MyPassport Pro all the time, but more like once or twice a year as a backup device for your camera, the battery might be damaged through constant drain of stand-by electronics. My last device died of this since...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

It all sounds confusing and over complicated but I can assure you that once the pieces are printed most of the process is fairly straightforward and the other parts to be used can be sourced quite economically. Finally, I will recommend a minimum...

... an STL file. The included STL was created while experimenting with TinkerCAD. It's still very much a work in progress, so suggestions and tips are welcome! Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Doesn't Matter Supports: No

I figured if I ever had a print that needed that additional ~5mm of build volume, then I will deal with new lead screws then. I also already have an Ender 5 Pro with a Dual-Z XL upgrade for a whopping 500mm Z build height, (but still only a 220mm X/Y...

Printing Select the vertebrae that you need and import them into your slicer. You will need to apply supports to the bony parts that stick out the back and to the sides. IMPORTANT: Be sure to label the vertebrae as they come off the printer! ...

Shoulders and Forearms (https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms) Armored Plate Carrier (https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier) Utility Belt/Waist...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...

Tools ==== * Soldering Iron * Allen Wrench (M3) * Super Glue * hacksaw or carpet knife Assembly ======== * Print the top, bottom, switch bracket and optional hemera bracket * Solder the two pin header to the back of the Duet3d PCB board * Fasten the...

Just put the LEDs and alarm speaker in a box with a labeled side (printed in white filament) and attach it to power supply fan connector... there is even a slot in my power supply cover to allow the wire to be slipped into (and out of) the power...

The single could be used in pairs at the junction point of the arches if desired or if your printer won't print the larger double base. I have supplied 4 different versions of the single with cable exits coming from different angles to allow for...

You’ll need a large printer for the Converter to accommodate the handles but it was necessary to print in one for strength (peace of mind when a £500 drone hangs in the balance). The phone clamp requires an 80mm M6 threaded bolt (I buy threaded...

... done, carefully install your Pi in the bracket, being careful with the pins and make sure all 5 pins go smoothly into the Einsy board. Click the Pi in place so the four printed posts in the corners are flush withe Pi's PCB. ...Snap the cover on.

The assembly takes about half an hour.Designed with Autodesk Fusion 360All parts are designed to be printed without material supports ### Parts to be printed - The main body (choose the model corresponding to your hotend : E3Dv6 or XCR-BP6) - The...

This is a ventilation system for an IKEA Lack enclosure.The top and bottom flanges have a “key” that will align the two halves so that the screw holes line up as well as the notch that can be used for servo and/or fan cable management if you wish to...

If you want to use Anet's original M5 screws/t-nuts, just print the parts with 100% infill and drill out the mounting holes with 5.0 or better yet, 5.5mm (to give you some alignment room) drill. Edit: Full screw list, as requested: * 10pcs of 412...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

- Dec 28, 2020*Revision 05 - Added Salomon Shift @ 301 BSL & updated BSL calculator - 1/13/21*Revision 06 - Added Fritschi Vipec / Tecton for QK/BF Mount @ 305 BSL, Added look pivot/Rossignol FKS @305 & 308mm, Updated BSL calculator, updated...

It doesn't cost you anything extra, but helps me out a lot :) Both links in this post are affiliate links. Print instructionsCategory: Hobby Summary Update: I added a second version of the top part of this case, which has a cut-out for those who...

... made it somewhat modular so you could make them taller or shorter. The outer pieces are printed in vase mode and just glued together.I used a 0.8mm nozzle for the outer transparent parts for some additional speed and rigidity.

Megacity Desert Habitat building for tabletop, expanded by rectangular build option.It contains:WallsRoof tiles with the capssome special sized doorssome basic bits for decorationYou may need to mirror the corner pieces in your slicer to get all...

Messuhr 20mm ******************************************************Update 16.10.2022Das Update beinhaltet 4 neue Dateien.Messuhr 20mm 05(16)-Skala (durch die Anregung des Makes von CHAOSXSPIRITMessuhr 20mm 05(16)-Gehäuse 2 mit verlängertem...

This is due to the different number of teeth in the printed gears for each axis. Feed rate changes the speed of the motors. Be careful to not move the azimuth axis too far so the stepper motor wire connected to the motor for the altitude axis...

All parts are printed, including hinge pins. I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to...

This design is intended to be a relatively affordable, simple and easy to print electronics project. Remix as required to add a secondary sensor, extra valves, etc. I have uploaded the most current Parasolid assembly file so feel free to dive into...

I wanted to have both a powerbank and a mobile lab power supply which are also protected by a corresponding housing, in this case the ammunition box, waterproof.I wish you a lot of fun and success in rebuilding...

Knobs Collection for Bolt Hex head and Nut This Hex Bolt Handle Set ISO 4014-4017 M2.5-M10 Links to used components: ISO 4017 Bolts Nuts AB Glue Epoxy Super Glue 502 E8000 Strong Liquid Glue Links to used tools: Mini Wireless Grinder Polishers...