3d printed fidget spinners

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

This was started on my Monoprice Select Mini, hence the size. Video Here: https://youtu.be/Ofxbj3s3f3A Print instructions You will probably have to do a little sanding or filing to get the parts to fit smoothly, but not much. I used thick CA glue to...

if your endstop position of your head is in the lower left but the print area starts 20mm to the right and 20mm up than you need to set this: ** **#define X_MIN_POS -20 ** **#define Y_MIN_POS -20** **#define Z_MIN_POS 0** **Enable EEPROM settings**...

If you print it to the right diameter, you might not need to drill it out, but getting an airtight seal can be frustrating. The Solidworks file is included if you want to adjust the hole size to eliminate the drilling process or use a different...

Build: Print the button and plate. Remove the support material. Fit the button into the plate to make sure they move freely. Trimming might be needed. Place the pen spring in the button and insert the button into the plate. Make sure the button...

My first prints with this thing showed an improvement, but only time will tell whether I was right. ;-) See the file Details.pdf for details and mounting sequence. Again, the Y-Carriage_for_20x20_V-Slot_Rail_Right and...

I printed it in a black PLA to help it blend in better with the Xbox. Edit - Feb 1st '21 - I realized that the smaller file's hanger's were off centered... so I have adjusted that and re-uploaded the stl. I have also included 2 more versions of...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

... better against the wall and feels stronger. - Chamfered the screw holes so they sit flush. - Increased the depth of the holder by 1mm to provide more space for the screws. - Printed in white instead of pearl white because pearl white looked dirty.

Failure to do this will likely result in decreased print quality. I tried several Z wobble upgrades but few fit right and the ones that are close don't secure the lead screw. I designed this based off of my Tronxy P802MA printer and I can guarantee...

I print at: X-9.4%, Y-9.4%, and Z-10% to provide a snug fit while keeping the height. Then I attempted to put super glue on the bottom to glue it to the bottom of the keycap. It worked but the key cap choc stem wasn't long enough to push down the key...

Check out more printing accessories from Department_Nine! ##Similar Designs## Found these after the fact (always hated homework): https://www.thingiverse.com/thing:4727323 https://www.thingiverse.com/thing:2994501...

It uses 2 locating dowels to press into the block's bellhousing pattern, and lines up to 3 bolt holes, so you can verify the print is accurate. Use this as a guide to hog out all the material within the frame. Note: before this stage, ideally, you'd...

This part is printed with support on the build plate obviously. In order to make it fit, you have to take the housing off of the USB hub (just slip a dull tool into the gap and pry, there's no glue or clips) and trim off the plastic at the end...

Print instructions: - AVOID PLA !!!!! - Use ASA or ABS for the mounting plate, I think PETG can be no-go if you has high temperatures in your case - Fan top, plates, etc… can be PETG - Use supports un fan top. - I put some antiwarping tabs on...

In the available file you will find also the letters if you want to have a 2 color print. Bill of Material: • OSOYOO 3.5” touch screen https://www.amazon.com/gp/product/B08634Y16L/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 • CSI/DSI...

Print the box STL files are at https://www.thingiverse.com/thing:2607585 6. Add the hardware Glue in the OLED display with hot glue. Cut a piece of strip board to hold the female headers to plug in the WeMos as well as a connector for the display...

Simple little print and fits great. I use the L6-30R boxes for my mining computers that are on a 240v 30amp outlet, Plus I have a 120v Lid I designed for a square outlet. When you use the outlets you need to trim off the tabs a little to get...

A modular board design helps with capturing the fine details of original design, as larger individual tiles can be separately printed even on smaller beds; additionally, the tiles can be easily stored. **Game Rules** Each player takes a set...

(Dimentional Accuracy is always suspect on printed parts so some sanding can be required to fit the magnets.)  Though it isn’t one-of-a-kind, the carnavalis stands as a rare and exceptional airship, originally designed by the visionary circus master...

I printed these parts using a delta-style printer, employing the following settings: For the Rings & Handle: - Layer height: 0.2mm - Outside perimeters: 2 - Top and bottom solid layers: 3 - Infill density: 20% full Honeycomb For the Clamps: - Layer...

(I should have used 12 mm/s.) Then i used an Image 2 Gcode program to create the gCode for the engraver using the 10 mm/s setting that I had chosen. Print instructionsCategory: DIY How does this Gcode test file work? This Gcode file will burn a...

Printed with CR PLA at 60mm / second 0.2 layer height with 0.4 nozzle 205 ° C hotend 60 ° C bed temperature 100% infill with tree support 45 ° --------------------------------------------- Deutsch: Dies ist ein Remix des Pi Drawers. Leider hat das...

By making it modular, I am able to print extra parts to allow the structure to expand and in doing so carry more coins, as many coins as needed. For me with 6 pontoons and one cup, I was able to handle a maximum load of 1.2lbs of coins. In the end,...

The design consists of 3 parts : 1) the base (about 4 hours) - 12% density zig zag support and 10% gyroid infill 2) the spindle (about 4 hours) 3) the screw (about 20 minutes) Note : spindle has been printed with different support angle. The outer...

* **Slides: sacrifice layer for successful prints** The track slides are designed with a 1-layer-thick sacrifice layer covering where the bolt hole transitions from hex-head area to round-shaft area. You can burn that thin layer out with a soldering...

Thank you everyone for everything, I appreciate all of you amazing people who've printed, shared and made dreams come true with my models, thank you for everything. ... Hopefully one day this will all get resolved and I can continue to share my models...

For printing: Use any material you like to use, but I would recommend PET at least for the rotary bolt to ensure the knob can withstand some impulse from the spring. Supports are usefull for the spool. Ensure that the control curve is smooth. Avoid...

The biggest part is 118mm x 141mm, so this can be printed on way more printers than the big version. There are now two LEDs per segment instead of three. There won't be much documentation as it's basically the same thing - just a bit smaller. So if...

Strengthened the nose of the vehicle by printing it in Ninjaflex 70% infill or ABS. 6. Created a new FrontWheelHub that allows motor wiring to enter at the correct spot. 7. Added hooks for motor wiring in the front part. 8. Stiffened the pushpin and...