3d printed fidget spinners

I would recommend printing with 100% infill. Included in the download is the sketchup source file for your own customization (Hint: I always include my source files). UPDATE!!! I still need to determine the pinout. I will post it up here once I...

Soooo, I bought a new Taranis X7, tore it apart, printed a new shell, and I can now present the Taranis Pistola! This allows for up to 8 normal channels of control, plus you can link receivers together to get 32. You also get all the flexibility of...

The other must have mod is the welding mask, I was able to unsnap some joints on a $10 mask and 'thread' it through the existing holder, then just use the top Velcro strap to attach to the front headband, better than a printed attachment - takes all...

The STLSs are up, I have validated Most of the Prints, but not the barge as of yet. I have done heavy design work on these models, however I consider them remix's due to the heavy amount of various Thingiverse parts, so credit where it is due. The...

There is a bonus version for those who can print multi-material with a Zelda Triforce design. While the two hooks on the sides do a great job of keeping the handheld secure, the hooks on the bottom and top needed slight tweeks. The hook on the bottom...

- Decreased gap to 5.4 to match the dial indicator (added 1.305mm spacer, with odd shape for printing without supports). - Changed hole to 6.53mm to match dial indicator, and made special bolt to act as a pin for a tight fit. - The hole is now 7mm...

For this, you will need a few parts: EzStruder direct drive or bowden doesn't matter Low profile motor support printed part (see my thingiverse thing) 30x30mm Fan shroud v3 (or other thingiverse thing version) 3 fans of 30x30mm (or different size,...

Since I have a large bed(300x300) I can print a standard sized spine in one go, and for the sleeve, the side panels are all intact. If you don't have that bed or you are going with a magazine format, you will have to use the one that cuts everything...

- Bottom diameter: select a diameter that your printer can bridge when printing the bottom pad. - Bottom thickness: determine how thick the bottom of your planter should be. That's not all - there are also complicated parameters to consider. The...

... the key « f » for fillets.</p><ul><li>Draw a sketch an the top circle under the helix with a little rectangle who will « join » the eagle wings. By doing that, you will have a better print by having less retraction.&nbsp;&nbsp;Category: Automotive

Install Klipper and make use of your Pi's processing power to speed up and improve your prints. There is a [good guide on reddit](https://www.reddit.com/r/klippers/comments/kj2h5r/stepbystep_guide_for_ender_3_v2_klipper_w_bltouch/) for setting this...

##You will need: - two MGN12 linear rails 400 mm long with MGN12H blocks - about 16 M4 hammerhead T-nuts (quantity depends on the required rigidity) - the same amount of M4x12mm flat head countersunk screws - about 16 M3x8mm socket head cap screws...

Make sure to print two! I haven't tested if the button inserts work, but there should hopefully be enough clearance for them. UPDATE 1/24/2023: Added a single piece back to the file list UPDATE 1/26/2023: Added some new models that should...

In the security set, you get: - Long & short barricade walls - Corner and straight connectors - Turret connector bases - 3 different defence turrets - Alarm siren tower - Security camera tower - Burn plate with fuel module All the parts are...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

Results Since I don't print ABS I don’t need to heat the bed up to 100C. I tested it up to 80 about 10 cycles and it now heats a lot faster even without any heat insulation underneath. I checked it with a pyrometer. This is obviously due to better...

The motor plate/gearbox must be printed with supports. A 3mf file is provided with suggested plating and support enforcement block specifications. Supports should only be specified for the gearbox portion up to the second bearing. Removing support...

They print at slightly hotter temperatures. Also, consider flexible TPU filament for the lid bumpers and the washers. The resilient material offers a quieter closure on the lid, and gives a bit of conformance on the nut tightening. The bumpers...

This allows it to be printed standing on its side with less support. With no supports, the top will have some drooping/stringing and some cleanup of that will be required. With supports there may be some residual support cleanup required. I use...

Print out little tabs for the aluminum plate. Total of 4 tabs were needed when using the 6″ x 6″ aluminum sheet. 3. Place the tabs on the top of the aluminum plate, then attach a metal circle around the plate's edges to keep everything in place. 4....

My version is intended for those who want to update their stock motherboard with a drop-in replacement such as the SKR Mini E3 or the Fysetc Cheetah so they won't need to print a new right case a second time. Instead of using TLSmoothers, I added...

This is my first attempt at sharing a 3-D printing model. History: A few years ago, after purchasing a CNC machine, I decided I would design a D-Handle that I could use for my Porter-Cable model 450 compact/trim router. I believe I came up ...

Except for the spacer ring, all parts are printed with ABS for stability and the possibility of stable gluing. The spacer ring is made of TPU. For adjusting the air gap between rotor and stator, the space rings are 1 or 2 mm high and can be...

hi,\r\nplease like if you enjoy \r\nthe green wall i made it pretty easy\r\nyou can extend the system with regular 80mm pvc pipe pieces\r\nit is also best to use sprinklers in the module reservoir but a hole will also do fine\r\nfor best results use...

If you decide to set it up just like me, you'll only print the front case STL. But if you'd like to set the LCD in the bottom position, you'll need the back STL too. UPDATE 2: Added a 40mm silent fan, enabled only when drivers are enabled and last...

to the picture).4) Zip-tie, screw or stick (doublesided tape) the gimbal controller to your plate.be careful that the m2 screw in the middle of the plate doesn't short out the controller!5) If you want print out this nice cover:...

... If you feel comfortable swapping filaments mid-print, try switching the white filament out for some clear filament after layer 2 can help allow more light to pass through. ## No Magnets I'm considering replacing the magnet indents with OpenLOCK.

For animated eye, use: * Circuit Playground Bluefruit -https://www.adafruit.com/product/4333 * TFT Gizmo https://www.adafruit.com/product/4367 Alternate is to use nogizmo_eye.stl * If using a printer that can stop and change filament, print pupil in...

Assembly I printed all parts with ASA, I glued the "5015Halter" to the component cooler with acetone. Fasten the "Grundplatte" with M3x10 screws. For the "Schlauchklemme" and the cold end fan, drill out the holes with 2.5 mm and screw in an M3...

I designed and printed this custom enclosure for the sensor using a Wemos D1 mini board (a clone will also work) and a DHT22 module. The DHT22 module, thanks to its built-in sensors, can detect the surrounding environment's temperature and humidity...