3d printed fidget spinners

I managed to get 280mm of print height out of the stock motors, and am using 16" z rods. When assembling the new frame, flip the X axis upside-down and backwards so the POM nuts are at the bottom inside of the arm instead of the top, meaning they...

The pieces I made to hold the bumper buttons haven't been printed or tested by me yet as I used hot glue in an earlier prototype piece. You can use just hot glue to hold them, but this may risk pushing them loose. The contact rings on the SparkFun...

base not included very high quality details i will update the files if you have special requests thank you so much for reviewing and commenting file updated 28th Dec 20 smaller cutted parts for easier print Spinosaurus (meaning "spine lizard") is a...

Edit 11/12/2019: I printed it out and it fits very tight, so you don't need to use anything to hold it in place. I saw a mistake somewhere and it's shorter than the original, but if you need it longer, you could edit it in the .ipt data. In my...

Left to our own devices to scour the net for solutions, (clearly we weren't the first people with CR10S Pro V2's to have purchased this product...right?!?) well after printing three different models that just didn't fit my setup quite right, I got...

Let me know if this was a good enough job that you would be excited to see more from me, and feel free to send requests I highly doubt this would print well with any other printer than a resin printer. I do not have supported versions of the files,...

... C'est un travail monumental que je mets gratuitement à disposition de la communauté, alors merci pour les Tips ! Bezain Print Settings : Printer : discoeasy200 Rafts : No Supports : No Resolution : 0,2 Infill : 30%

Bill of materials: Printed: 1 x CASE MAIN 1 x CASE FACE Bought: 5 x Banana sockets of different colors (https://item.taobao.com/item.htm?spm=a1z09.2.0.0.67002e8dUgkbaW&id=561956389062&_u=52q9f1426ddc) 1 x Potentiometer 50k Ohms...

... let me know in the comments! Printer: Flux Delta Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 80% Post-Printing I designed this using OpenSCAD, and it was a total pain! ...I'm going to have to learn SketchUp or something one of these days....

Preparation: Print 2-3 models of the crayfish for students to examine better. Students need their science journal and a copy of the crayfish worksheet (front being the diagram and back being the function sheet). For parts 3 and 4, you will need live...

Test this :) !!! Printing Info : - use a materials that is stable in water (I used PETG).- use support from build plate only. - optionally add more part cooling to make support removal more easy. Why I made it : I made this...

What you will need in addition to the printed parts: Six, 6-32 by 1'' Mechanical screws and matching hex nuts. (Close dimensions will also work, the slots have some play to them) One or two small springs, approx 4mm diam. x 20mm. These are optional...

When printing these models, it's highly recommended that you use Cura's "Horizontal Expansion" feature with a negative value. A value of -.12 works for me. If they are still too rigid, try -.15, then -.20, and so on. Introducing BuckleBoards, a...

Stylized Earth Python Generator is a Cinema 4D scene that enables quick creation of a unique representation of Earth by leveraging inspiration from dot matrix printing. Instead of ink dots, elements are created with mesh that wrap around a sphere. In...

Using an M3 tapered tap, I found it was relatively easy to slowly do this with no pre-drilling.The thread will, of course, not be complete and that is why a long screw is used in fixing.Assembly:Two M3 nuts should be pressed into the back of the...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

 PLACING IT ON THE WRONG LEG IS A HIGH RISK TO YOU.You could use this mechanical design and limit switch to interface with the low-voltage system, but you will have to provide the required software modifications.There are several adjustments...

It would be fascinating to use a glow-in-the-dark filament to print this part of the model, then recreate the experiment using a UV light. Understanding the function of proteins is a crucial aspect of a biology course. Specifically, students must...

It's a relatively simple print. To get this up and running, you'll need the following: 2019-03-02: I updated the design because the old one allowed big bugs in, and they got cozy on the Raspberry Pi. This new version should be bug-free. I also...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out.Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. Pay...

If a defined limit is exceeded, a signal is transmitted to OctoPi and the print is paused.Zusammenbau/AssemblyElektrische Bauteile/Electrical components:Die benötigten elektrischen Bauteile können dem Schaltplan entnommen werden./The required...

Most PC fans should fit since there aren't any thickness constraints, if you have a thicker or thinner fan then the parts will fit around this.The fan is modular so you can print what you want and perhaps design your own parts. I've included the...

Print one and check for fit. Make micro adjustments in the X & Y axis of your slicer if the rod cap is too tight or too loose. There are Left & Right 3MF file versions with built-in supports. There are also STL versions with supports if you prefer...

... If you want to create a stand for your transmitter, print two "X10S_stand.STL" parts and attach them with a standoff. I've also included a JR module bay cover, remixed from https://www.thingiverse.com/thing:513861, which has space for angled pins.

2-4, 3-4, 4-4 and possibly paint in the depressions or just print without a lid.. The lid text is available in German & English !!! There are covers for protection and cardboard parts for the round targets and starting players. The card...

BASIC PRINTING INSTRUCTION FOR EACH PART ARE IN THEIR NAME FOLLOWING THIS LOGIC: [model name (base if common to most][part name][helpful assembly info, mostly left or right][ (need support) if needed][how many are needed if more then 1] Unlike my...

This is inspired by Zack Freedman's weighted Gridfinity baseplates, but puts the weight cavity on TOP so that the model needs NO SUPPORTS to print. As with all my other Gridfinity models, this was designed using CadQuery instead of Fusion 360. See...

Print Settings Printer Brand: LulzBot Printer: Mini Rafts: Doesn't Matter Supports: No Resolution: 0.2mm - 0.3mm Infill: 30% Notes: Nozzle size used: 0.5mm (any should work) Shell thickness: 2 perimeters (1mm in my case) Top/Bottom Thickness: 1mm...

UPDATE: I have reworked the top and bottom of the case so that it can now be printed without supports being turned on. I have also moved the USB and Ethernet port partitions to the top half of the case to ensure their stability when installing the...

Threads of diameters between 3mm and 10mm have been successfully printed, but you can use any diameter for your designs. Thread shapes are similar to ISO METRIC standards but not identical. Initial tests using screws and nuts from this library...