3d printed external hard drive rack

To secure a hard drive on a stable base, you'll need a few easy-to-use mounting solutions. ...These mounts require six (#6) wood screws for installation.

A DIY project - a custom caddy crafted to secure a 4TB portable hard drive, specifically designed for use with the Netgear Nighthawk router when it's wall-mounted.

Typically, damage occurs when a hard drive and its housing collide during a fall, leaving the electronics intact. As a result, they sell the same PCB separately. I purchased twenty adapter discs from Toshiba Store Alu 2S USB 3.0. The enclosure can be...

Typically, damage occurs when a hard drive falls, resulting in a cracked housing but intact electronics, allowing you to repurpose the PCB. The Toshiba Store Alu 2S USB 3.0 enclosure serves as a reliable starting point for this project. ... Links to...

Using two strong hard disk or hard drive magnets, the latch magnetically adheres to the gate surface. At the same time, the iron rod (ikea curtain rod) also adheres to the magnetics so it can stay up yet still slide down when needed. This gate...

This holder combines a 3.5 hard drive bearing and the parts you print and 5 total screws and 2 t-nuts. On my application, I used M4 x 8mm screws and M4 t-nuts to secure the mount to the rail. I reused the screws from dissasembling the hard drive...

This holder combines a 3.5 hard drive bearing with the parts you print and five total screws and two t-nuts. On my application, I used M4 x 8mm screws and M4 t-nuts to secure the mount to the rail. I reused the screws from disassembling the hard...

As a non-3D printing veteran, I'm about to take the plunge and order my first printer. It'll arrive in a few weeks, and then I'll be able to print this design out for real. SolidWorks file included for your reference. ... Build Time: 16 hours and 31...

It has the side mounting holes for the 2.5" drive and it has both the bottom and side threaded holes to fit in the 3.5" caddy, matching the same specs as a Seagate hard drive exactly. Uses around 10 grams of plastic. ...Works with a set of four or more...

... sell them without RMAing the whole unit, which wasn't going to happen. You'll need 4 x #6-32 countersink screws to attach this rail assembly to the hard drive. ... I recommend printing this design with a 0.1mm layer height with 100% infill.

It securely holds one 3.5-inch hard drive in place. To ensure perfect symmetry, simply replicate this design for the opposing rail. ...The provided anchors serve a crucial purpose by preventing warping during the printing process; once complete, they...

Hard drive magnet are kidney form like https://www.thingiverse.com/thing:4858583 Hard drive magnet are strong magnet... be careful! Need to add support for the trex head, but no support for the magnet. The fride-magnet-[Something]_2.17.stl is...

To build your own Raspberry PI NAS tray, follow these easy steps: Step 1: Print the custom tray design Step 2: Cut away the latch support as shown in the image below Step 3: Install your hard drive by pulling out the side latches and fitting it...

Hard drive magnet are kidney form like https://www.thingiverse.com/thing:4858583 Hard drive magnet are strong magnet... be careful! Need to add support for the horse head, but no support for the magnet. The fride-magnet-horse_2.17.stl is for...

I designed this upgrade specifically for my HP Elitebook 2540p, planning to swap out the hard drive, a move made trickier by the lack of new 1.8" uSATA hard drives from the manufacturers themselves. This design fits perfectly onto my laptop using an...

... holder, which wasn't enough for my needs, so I created this attachment to add two more. ...This design mounts the additional hard drives on the exterior of the case, elevating them above the upper edge to prevent any pressure on my large graphics card.

... a 2.5" hard drive without need for screws. ... It is designed to hold the hard drive only with friction, so the accuracy is relatively important (or you can add pieces of paper to make it secure). ... -Added .step file -Added pictures of the adapter

... the need for screw installation. ...This device holds the hard drive securely in place using friction alone, making precision a key factor in its functionality. ...To enhance stability, users can also insert small pieces of paper to reinforce the hold.

... deux disque dur. Hard drive bracket width 145.8 mm for two hard drives. Version V.2 I made a slight modification to the back, which seemed too lengthy to me. ...Version V.2 I slightly shortened the back panel, as it initially appeared too extended.

... than before. Materials needed: * An M6 bolt or similar size to fit your TV's VESA mount * A few elastic bands to hold the hard drive in place Note: My hard drive is a Toshiba model, and I designed this holder based on its dimensions - 119x79x15mm.

Color: Red, White, Black, Multi (PolyJet).Red: 2 Side plates; 2 Rev mounts; 4 Motor spacersWhite: Team NumbersBlack: Main frame; Screw pieces for mecwheel lockPolyJet: Stratasys logo

I needed to mount two 3.5 in Drives in this chassis so i made this printed off three times to get it correctI used a couple of wood screws to secured in place With some 3D printed things

This innovative design holds the hard drive in place solely with friction, ensuring a snug fit that's crucial to its stability. For added security, you can incorporate pieces of paper to reinforce the enclosure's grip on the drive. **Updates:** *...

Multi-bay ventilated rack designed to organize and securely store your USB hard drives. This model is optimized for printing vertically with no supporting material required. Precompiled STL files are available for HDDs measuring approximately 113mm x...

The script enables a customizable mounting bracket for use with the Inateck FE3001 Aluminum USB 3.0 Hard Disk Drive Enclosure. Product link: https://www.inateck.com/inateck-fe3001-3-5-usb-3-0-superspeed-hdd-external-enclosure.html The bracket can be...

Designed for this drive: https://www.microcenter.com/product/486116/inland-35-usb-30-hard-drive-enclosure - but may fit others too. Drive has 32mm depth and the screw holes are designed for #8. ...The arc at the bottom isn't quite right but it...

... two M2 screws to secure the carriage. ...You'll also need 4 hard drive screws that have a tapered (countersink) head (this is a requirement as there are very tight tolerances on either side of the hard drive and there is NO space for screw heads.

A simple and universal adapter to install one or two 2.5" laptop hard drives into a desktop computer. Allows for the 2.5" drives to be offset for right angle cables if needed. One of the models is a simple print and use version, just print them two...

Hard drive sled for IBM PS/2 models 76 and 77. ... The IBM FRU numbers for the original sled are 96F7775, 71G5706, 71G5708, 79F3300 Hope it helps someone :) 32K

Needed a 2.5 15mm hard drive mount for my 5.25 bay but could not find anything so I created this. Also supports a 120mm fan to keep everything cool. ...You will need 3 spare 5.25 bays.