3d printed dust collector

Cap for 2.5" Male Fitting for Dust Collector System, sourced from Fusion 360 at http://a360.co/1RvO7ME. ...The conversion piece from 4" to 2.5" can be found by visiting http://www.thingiverse.com/thing:1444225.

I've designed this dust collector as a quick print with easy add/remove parts. The main body is held in place by the 775 router motor itself. To assemble it, remove the motor, slide the dust collector assembly over the motor mount, and then...

There are vacuum drill dust collectors available on Thingiverse, as well as adapters for Dyson handheld vacuums. However, I couldn't find a single-piece vacuum drill dust collector specifically designed for the Dyson V6. So, I decided to combine...

I did notice a slight gap between the base & the dust collector itself. I didn't want to print it for 20+ hours to find out it wouldn't work so I remixed it a bit. I also put a couple of intake vents underneath to allow for air inflow. Not sure...

For the adventurous ones, I've attached some pictures of my Led installation inside the dust collector and nose. This is completely optional and will require some soldering and wire routing. Part Body_C has a little slot to fit a led strip and make...

This is a dust collector hose clamp that attaches to my lathe banjo to hold a flexible hose. I mainly use this for turning small items such as pens. The flexible hose allows me to adjust it to get the best dust collection. I used a 2 1/2 and 4 1/2...

This simple design of a dust collector for the Comgrow Robo CNC fits around the mounting block of the z axis step motor. There is still some work in progress as with the vibration the collector moves a bit up. I have created a possibility to...

A Shapeoko dust collector attachment, printable in several parts for easier printing convenience. Requires four neodymium magnets with a diameter of 10mm and a width of 2mm: https://www.amazon.com/gp/product/B07CNBSMDZ (or any equivalent magnet). ...

I was using a dust collector vacuum to remove loose fill fiberglass attic insulation. Needed a connector to splice two of the 4 inch hoses together. It was X-mas eve and the stores around me were closed. Couldn't find an existing design online, so I...

I highly recommend investing in a DeWalt DW 745 dust collector - it's been a total game-changer for me. ...The real challenge comes when the dust starts flying everywhere and you don't have a vacuum attached, but fortunately, plugging in this bad boy...

The edges of the ergonomic shape allow you to press the dust collector to the ceiling, and the tight fit of the dust collector to the surface eliminates the release of dust. ...</li> <li> It is better to use this device together with the drilling...

drill dust collector, but most of them are too big for me - so I set out to develop my own, which can stay on the drill and takes up all the drill dust, so that when you drill you do not have to mask all smoke detectors.Through the tab on the side,...

# Dust Collector Adapter for MakerMade M2 ### Description This is a tapered bushing that allows you to connect a large shop vac hose to dust collector port on the M2 sled. ### Files I drew the part in FreeCAD and have included the file, in case...

Swing arm joint for a 4 in dust collection system. ...It uses 3d printed bearings where the air flows through the center of the bearing. Designed to work with 4 in triple wall drainage pipe available at HD. ...

I designed a specialized dust collector specifically for the Ryobi Hand Vacuum cleaner, crafted with a precise 45-degree angle to ensure optimal performance. To minimize dust accumulation, I opted for an extremely thin layer thickness of just 0.1mm....

This is a dust collector hose clamp that attaches to my lathe banjo to hold a flexible hose. I mainly use this for turning small items such as pens. The flexible hose allows me to adjust it to get the best dust collection. I used a 2 1/2 and 4...

... that operating the device in conjunction with the sandpaper generated an enormous amount of dust. ...Determined to streamline my workflow, I took matters into my own hands and designed this dust collector to seamlessly integrate with my vacuum cleaner.

I did notice a slight gap between the base & the dust collector itself. I didn't want to print it for 20+ hours to find out it wouldn't work so I remixed it a bit. I also put a couple of intake vents underneath to allow for air inflow. Not sure...

This is a dust collector for Makita 125 mm angle grinders. I designed it for the GA5030, but it should fit all Makita angle grinders with the same style of clamping. To assemble you will need: - 1pc screw M5x16 DIN912 with nut DIN934 for clamp -...

More stable version of the wallmount for the Cyclone Dust Collector from Endlesscnc With pin so you can easily fix an unfix the cyclone Stabilizations are provided in the model at critical points so you can go with a infill of 15 - 25 %

Drill dust collector for SDS for ceiling holes. If you like it, I'd appreciate your support. You can donate via PayPal to help keep my content free and available online. ...Click the link below to contribute: https://paypal.me/fafabienman

This simple design of a dust collector for the Comgrow Robo CNC fits around the mounting block of the z axis step motor. There is still some work in progress as with the vibration the collector moves a bit up. I have created a possibility to simply...

My shop is compact, so instead of hard-piping my tools directly into my dust collector, I use a single flexible 4" hose that I can easily move from one tool to another. This setup connects a standard flexible 4" dust collector hose to the 4" port on...

The adapter plate and nozzle turn the HF Tools $40 yard blower/vac into a 3-micron dust collector. The plywood plate is optional, planned for mounting to a wall or attaching to a cyclone dust separator. This combo moves more air than a 6-hp shop...

I am looking for testers to give feed back!Update March 29 2022**V2 parts uploaded- Cap and Intake broken up for ease of Printing** multiple Intake tubes sized to accommodate different flex pipe tubesAny constructive info can be posted on Twitter...

Update March 29 2022**V2 parts uploaded- Cap and Intake broken up for ease of Printing** multiple Intake tubes sized to accommodate different flex pipe tubesAny constructive info can be posted on Twitter (tag 3Dprintingllama) or e-mailed to me at -...

This is a dust collector, guard, splitter designed for saws lacking standard riving knives. The built-in riving knife ensures efficient dust collection for square cuts and attaches securely to the throat plate via a bolted block and cross screws.

This is a customizable dust collector designed for use with 400w CNC spindles, featuring an adjustable height that can be easily fine-tuned using a wing nut. The aluminum tubes provide stable guidance while also functioning as suction pipes, ensuring...

Inspired by Karl Wiliams dust shoe: https://www.thingiverse.com/thing:325805 I created my own from scratch. This is version for 2.2 KW spindle of 62-63 mm mounting diameter. Made from 3 sepatate parts. Is very easy to print. The one I've printed...

... vacuum cleaner for this purpose, dedicating it solely to this task. If needed, I can always upgrade to a larger model and use the existing one elsewhere in my shop. To facilitate connections between components, I 3D printed several custom parts.