3d printed cord holder

The printed gear wheel has a wide spot in the gears with a 3mm hole and space for a nut on the inside. To keep everything secure, I filed a matching flat spot on the rod where the gear fits. Assembly is relatively straightforward: 1. Check the...

It is a simple flat top that can easily be printed upside down and has an included thread to put in a typical Bowden tube fitting. Please the picture and the model for more information.March 7th 2023 Update: Looking at the design I realized the hot...

A massive project undertaken by my tabletop group to play BattleTech, which faced challenges with both printed maps and hex-sheet setups due to persistent forgetfulness of terrain and later issues with terrain pieces getting knocked around on the...

12mm tubes have been tested, and test prints are being done with PLA. The fitment of the connectors may not be the same with different plastic combinations. Ideas for improvement include using TS Twist Plug to stop any ports up that aren't being...

If I had included lips or ledges, the resulting tree would have been too narrow to print smoothly. Take a look at my other trees and their bases if you want to see what I'm talking about - just click on these links:...

Endstops The Y-Axis endstop is a single mount for both front and back switches, activated by two tabs mounted under the bed with M3 screws, nuts, and printed M3 T-nut converters. The upper Z-Axis switch is clamped to the Z-Stepper motor RHS...

Print two of each part, cut two 3-inch pieces of copper pipe (cut extras for replacement when the anode disintegrates). Assemble as shown in pictures; hook up solar panel. Hose clamps connect panel to electrodes, keeping them from slipping out of...

There is a printable bearing race included for the idler pulley which works well (print 2 of them). You also may want to lube the spring housing interior with a teflon based lube to allow easier sliding since sanding inside the housing will be...

Edit 27-10-2018: added the Fusion 360 original This is a second, improved version of http://www.thingiverse.com/thing:1526752 Detachable top part - easyer for transport RGB Color LED for status More sturdy frame Improved software Smaller electronics...

I'm looking forward to rolling up to my next conference and busting out a laptop printed into a Pelican case. A full description and build guide can be found at Oceanography for Everyone. Support more projects like this by contributing to my...

Create your own Porsche 911 rsr button box for your cockpit If you need stickers, message me at jose_as24@hotmail.com after purchasing the model you can order the .dwg file for cnc machining PARTS NEED FOR THE BUTTON BOX 12mm momentary push...

Instructions: - Use the following options to personalize your back to school nameplate: - Center: 0 - Rule font: write/knewave.dxf - Rule Decoration: txdes - Build Plate Selector: 0 - Read: 1 - Text Height: 5 (Text_Height) - Length: 190 - Text Height...

I extruded the design to 1mm, added some fillets, and printed it in PETG. Worked the first try (instead of requiring the expected two redesigns). For those still following along, I installed the video card with the new PCIe bracket into the QNAP....

I also made some minor tweaks to make the counters look better for 2 color printing. Use layer height of 0.2mm and set your second color to start at the 14th layer. Update 4/22/2019 -- Treasure, Brick, Exert, and Embalm tokens released! Treasure...

I recommend printing "Re-ARM-fan-endpiece.stl" first in your chosen material, and then verify it fits the 80mm fan. If it doesn't fit, you may need to calibrate the extruder. Thanks to the following people for creating the models which helped me...

PARTS NEEDED: Front Wing: 2x M3x12 (to mount the wings) 4x M3x8 (to mount the endplates) 2x M4x12 (from the stock front bumper, to mount the front wing mount) Rear Wing: 4x M3x12 (to mount the swan neck mount) 4x M3x12 (to mount the wing onto the...

Other Projects Tamaguino http://www.thingiverse.com/thing:2120692 https://alojzjakob.github.io/Tamaguino/ Website Traffic / Like Monitor with NodeMcu http://www.thingiverse.com/thing:2286288 Print Settings Printer Brand: Wanhao Printer: Wanhao...

500gm spring coils...

You can also see that i need to fix my cooling duct and print out a new one as bridging is still not as good I then screwed back the webcam to the mount and placed this on the y carriage of the printer and in this way you dont need any screws or nuts...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

Mine is printed using carbon fiber PETG for the body and translucent green PETG for the top. I'll list out the specific electronic and mechanical hardware that I used below, I know this combo works and pretty damn well at that. If you don't wanna...

Also (constructive) criticism or exchange of experiences is welcome! Post-Printing Sketch für ARDUINO: int topleft; int topright; int downleft; int downright; int drehen; int heben; void setup() { pinMode(8, OUTPUT); //Heben / Senken pinMode(9,...

In fact I most often just grab these instead of my actual metal bench dogs unless I really need the sturdiness or precision that my metalPrinting InstructionsYou should be able to get away with 0.2mm layer height easily, the XY-resolution is more...

I have tried to keep the parts list as simple as possible (not including the many printed parts of course), and those parts which you will need to purchase are easyto acquire. Disclaimer time: The project involves the full disassembly...

It prints in three parts, so that you can print all of them on a flat face with no supports. The pack charges using a 2S balancing lithium battery charger, hence the JST XH 3-pin connector. You should try to find one that supports charging at...

In fact I most often just grab these instead of my actual metal bench dogs unless I really need the sturdiness or precision that my metalPrinting InstructionsYou should be able to get away with 0.2mm layer height easily, the XY-resolution is more...

This lathe features: - main carriage knob to intuitive movements, 2.5:1 - reinforced and dust protected tool carriage with C-Beam profile, two sides driven - continuously variable speed via a cheap VFD BLDC controller - fixed tools turret with two...

Simply print the base and cap and 14 disks (mark one of them or print in different color). I recommend rethreading bot cap and base with M12 (that's how i did it) or scaling the cap up a little in x/y. The rules (thanks to...

Otherwise you may PERMANENTLY DAMAGE your lenses due to the glue vapors as they will stain and ruin your otherwise clear glass. I did some light sanding on the inside of the adapters so that they slide on and off more easily. Qwerty_Uieo made some...

Old School will likely require some servo extensions. Notes: Printed in eSun PLA+ Arrange parts on the build plate according to the illustrations. Cura: Support Touching Build Plate, Infill 15% Trim away the 2 little locking tabs inside the slots of...