3d printed computer accessories

I suggest printing the top pieces in something more heat resistant than just PLA, preferably carbon fiber nylon or polycarbonate. ASA should work pretty well too. For the bottom pieces, I used PETG as it allowed for the cards to slide in and out...

... amélioré : plus esthétique (et d’autres éditions spéciales;) ), système d’éclairage led, etc. Pour suivre ces améliorations, n’hésiter pas à vous abonner a ma page Thingiverse et Facebook : https://www.facebook.com/waikikiprod Bon print à tous !

That said; I'm still using it, and in the context of how I want to use it, it's much better than the tray I had designed, and better than the other thingiverse smoother cases I have seen/printed. So consider it as a silly idea that's going to work...

The STLSs are up, I have validated Most of the Prints, but not the barge as of yet. I have done heavy design work on these models, however I consider them remix's due to the heavy amount of various Thingiverse parts, so credit where it is due. The...

The STL file itself prints flat and then will need to be bent with a slight angle in the stem. This can be accomplished by running the stem under hot water or dipping it in a bowl of hot water to soften it a bit, and then using a pair of needle...

to the picture).4) Zip-tie, screw or stick (doublesided tape) the gimbal controller to your plate.be careful that the m2 screw in the middle of the plate doesn't short out the controller!5) If you want print out this nice cover:...

#Installation instruction: ##Hardware: Print, sand, use some hot glue to attach the screen to the shell and to glue them together. ##Software: Requirements: none for standalone version www + php server - in my case Lighttpd + PHP on Raspberry Pi 3+...

... Some part coolers like the "Petsfang" & "Bullseye" seem to crash into the camera housing during autobed leveling. Many thanks to "acwest" for pointing out that problem and his solution! ===================================== Have fun printing!

Then print it out together with a T-piece. Glue it together in the slicer, so to speak. That's how I did it with the glasses box, or with the mini-Jo ;-), both of which are not mine, I just put on the T-piece. And I also had to think about...

Hardware needed: 18x M3x8 (or longer) bolts 18x M3 nut 1x M8 threaded rod for spools (length 172mm when fixed midway of box height) 2x M8 nuts and some washers as spacers between spools 2x Pneumatic air quick release fitting with 6mm diameter thread...

This lifts the cables to eliminates contact and flexure of the cables during printing and it eliminates/obviates the need for chainlike cable housing to hold the cables and distribute/minimize flexing and possible wire breakage. ...In return, your...

4.) Time to choose colors for printing. Going all lime green, it looked nice because I thought this vibrant tone brought a certain brightness when laid on a dark or otherwise subdued backdrop which always helps capture attention wherever applied...

... for the electronic you can use pro micro, smt32, or leobodnar bbi board FOR PERSONAL USE, YOU CAN'T RESELL THE DESIGN, THE FILES NOR THE FISICAL PRINTED DESIGN, YOU CAN'T NEITHER SELL ANY MODIFICATION OR DERIVATIVE OF THE ORIGINAL MODEL

The pieces are printed with 50% infill, 10 layers of 0.15, 4 perimeters. Only the engine support may need supports (see image). ... Equipment: GT2 pulley 16 teeth for 5mm axle 142 (or 140) mm GT2 belt 3 CHC M3x16 screws 3 CHC M3x8 screws (or headless...

Print the "_withbutton" versions of the bezel and frame, as well as the button cap. Insert something squishy (o-ring, piece of foam, rubber band, etc.) between the pushbutton and the button cap. A Raspberry Pi Zero W could be used instead of the...

Thank you everyone for everything, I appreciate all of you amazing people who've printed, shared and made dreams come true with my models, thank you for everything. ... Hopefully one day this will all get resolved and I can continue to share my models...

Print it with 0.2 and 100% infill. IKEA LÖRBY (EUR 9.99) is a USB charger that's powered by a 24 Volt power supply. It delivers a total output of 3.4 Amp and an maximum output of 2.4 Amp per USB Port. This makes it compatible with the Ender 3 power...

Update 2022-01-17: I've started adding .stl files for Ender 3 based on measurements provided by [Nolemgib](https://www.thingiverse.com/nolemgib) (top: 25cm with screw holes, bottom 13cm with cutout at one end, vertical half 20cm (40cm can not be...

... albums of all time, and they ranked Hendrix as the greatest guitarist and the sixth greatest artist of all time. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D

(I've worn them and they're actually not uncomfortable) List of the parts needed to print: 2x Nanami_rim.obj 2x Nanami_pads.obj 1x Nanami_nose_bridge.obj The rims are perfectly symmetrical, so don't worry about having to mirror them or anything. The...

**Gravitrax Ball wheel V1** - Difference in height 80mm - no support necessary - 3 pressure parts: wheel, gear, pillar - Printing time approx. 6 hours - you need: (motor see links) 5 x magnets Ø 5mm x 3mm 1 x M4 screw 45.0mm or longer or threaded...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

*** Do not print this in PLA as it will melt or sag inside the car *** *** You must provide a charger *** This design is tailored for a 2019 Highlander, but it should also fit 2017-2019 models; I am uncertain about compatibility with other years. I...

The lamp used in this setup is an Aglaia 4W LED touch-control lamp featuring a clamp base that was removed to accommodate a longer M6 x 20mm screw for mounting on the printed bracket. The non-conductive material of the bracket prevents electrical...

A massive project undertaken by my tabletop group to play BattleTech, which faced challenges with both printed maps and hex-sheet setups due to persistent forgetfulness of terrain and later issues with terrain pieces getting knocked around on the...

You'll want to print two of them and ensure they both line up when drilling your holes. The X alignment (side to side) is absolutely critical for the drill guide, while the Y alignment doesn't really matter. Update 3: A new version of the Combined...

print a large end and glue it to the screw head. I'm attaching this as a .STEP file... I'd rather you take a look at this F360, Freecad, etc... it works great as is, but I'd love to get some feedback. I'm open for any suggestions on...

For the same price of one tent pole could buy 2 x 6.5m lengths of Al tube, and a roll of filament. Took a few attempts but the twist lock cams were very easy to design and print and worked far better than expected.  The larger version...

Instructions You'll need 4 of the mosaic feet, and four endcaps - each should be printed with a .3 layer height and no support using an infill level of 15%. As for me, that was enough. A 5/16" length of threaded rod will come in handy as well as...

------------------------------------------------------------------------------------------------------------------------ Old Description...