3d printed chain

Simply print the base and cap and 14 disks (mark one of them or print in different color). I recommend rethreading bot cap and base with M12 (that's how i did it) or scaling the cap up a little in x/y. The rules (thanks to...

I have to find efficient part cooling solution, this one does not cool enough with speeds I am printing now. VERRY IMPORTANT! Use correct lenght screws for motor mount. Slightly too long and mount points will be ruined! Parts needed: 2x 445mm X...

print the uppers in a 100% infill! Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

500gm spring coils...

Old School will likely require some servo extensions. Notes: Printed in eSun PLA+ Arrange parts on the build plate according to the illustrations. Cura: Support Touching Build Plate, Infill 15% Trim away the 2 little locking tabs inside the slots of...

All other things still apply like changing the name of the .txt files to .h and .cpp respectively.  Printing:All parts saved as STL are in the correct orientation, and the only part that needs supports is the head. It only really needs...

I printed this in PETG and was able to get it in place with some firm pressure that caused some temporary deformation of the outer shell. You should still be able to get it pushed in if printed in a more brittle material, like PLA, but be careful not...

(And why on earth is Print Screen so close to the Page Down button, anyway?)Mice and trackballs were obvious options too, but just like the keyboard, they required more precision and dexterity than I could muster on the move. I even tried a couple of...

The models should already be scaled at 1/100 and we recommend interested tank crews or potential cadets new to the hobby to print out the models through an expert printer for tryout. Like the models we posted? Feel free to support us on...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

Take care to observe that the orientation of the toggle switches (especially the mode switch) corresponds to the printed labels. 9. Connect cables to control board, then mount control board to the standoffs in the control box. The board is to...

I printed the right and left halves as provided, with no supports but one side had to be flipped 180 in the slicer app. I couldn't do anything with the provided whiskers that stand on-end so I made some up. I decided on 3 different length of...

Whether this means organizing drawers, creating a catch all tray, setting up a bedside charging station for your devices, or even creating a wall mounted shelving unit, this system can do it all.I had success printing these at a 0.2 mm layer...

This lathe features: - main carriage knob to intuitive movements, 2.5:1 - reinforced and dust protected tool carriage with C-Beam profile, two sides driven - continuously variable speed via a cheap VFD BLDC controller - fixed tools turret with two...

Its light and super stiff if printed in ABS 100% infill. Included are all the .STL files for all the models. The frame is quite light and stiff. I threw the frame over and over against a wall and from a 5th floor balcony and it survived...

Like "M9999 S1" S1 = song 1 / TETRIS S2 = song 2 / CREAZY FROG S3 = success sound, when printer is finished with printing S4 = bad sound, when something failed first about the lcd: its very easy to make the i2c lcd supported... get the cheapst...

Une possibilité de réglage latéral sera prochainement ajouté MAJ du 30/07/2023 Mise à jour du support de 2e axe et du porte écrou pour un réglage facile du parallélisme latéral de la tige trapézoïdale associée...

In fact I most often just grab these instead of my actual metal bench dogs unless I really need the sturdiness or precision that my metalPrinting InstructionsYou should be able to get away with 0.2mm layer height easily, the XY-resolution is more...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

I printed the right and left halves of the mask as provided, with no supports but one side has to be flipped 180 in the slicer app. I couldn't do anything with the original whiskers that stand on-end so I made some. I decided on 3 different length...

In v1, a massive block in the middle was supposed to do that, but these two smaller ones do the job just fine and we save some material in the process. While printing, however, I thought of a slightly different way; v2 slides horizontally over the...

Print both parts of the holder (see printing instructions) 2. Use 4 small and short screws to attach the board to the horizontal plate as shown on the photo (mind the orientation of the plate!) 3. Glue the horizontal plate into the main holder from...

I have tried to keep the parts list as simple as possible (not including the many printed parts of course), and those parts which you will need to purchase are easyto acquire. Disclaimer time: The project involves the full disassembly...

Mine is printed using carbon fiber PETG for the body and translucent green PETG for the top. I'll list out the specific electronic and mechanical hardware that I used below, I know this combo works and pretty damn well at that. If you don't wanna...

Well, the possibilities of PrusaSlicer (and probably other slicers too) give you the tools to realize this yourself, with a good dose of creativity!Principle.The articulated model is supported at several points with printed springs which in turn are...

(A mixed approach is to also create the base with this program, and then add as a part something made with the Name Tag creator, but it's actually more hassle and basically the same process.) Note that the Name Tag creator works well alone if you...

steps per mm, UBL. -after doing UBL make sure you turn BL on (in the same menu as UBL -- BL : on is displayed) -make sure you save everything to EEProm -start printing and be ready to fine-tune your first layer with the “Babystepping” – do it in...

1x - 1000 Ohm resistor 2x - 10000 Ohm resistor 1x - momentary button switch...

My some other things: <img src="http://things.ruvim.info/img/Disc-Sander-Duo.-D50mm,-D75mm.jpg" alt="Disc Sander Duo. D50mm, D75mm" title="Disc Sander Duo. D50mm, D75mm"></a> <a...

My some other things: <img src="http://things.ruvim.info/img/Disc-Sander-Duo.-D50mm,-D75mm.jpg" alt="Disc Sander Duo. D50mm, D75mm" title="Disc Sander Duo. D50mm, D75mm"></a> <a...