3d printed carabiner

The built-in socket has the advantage that no cables can be seen. Tools you will need: (see the pictures) Hot glue, super glue, soldering iron, screwdriver, ... Print instructionsCOMPONENTS: Attiny85...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

The box back design for each car is similar in design since I want it to be seen as a set.Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "300ZXBoxBack":1) Start (Colour of the...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

Proceeds will be used to purchase printing filament so I can keep testing and designing cool new things that you might find useful. Thank you! Note: Have a look at my other designs, I have some nice sharpening accessories for all your knives...

blue lines or infill) should be ignored. Post-Printing Assembly Guide Tools needed:* ca 10 wooden toothpicks, 2mm diameter white glue. The one that dries in 5 minutes works best for me.</li> <li>adhesive tape to keep pieces in place, while the...

Well I am just to lazy to print twice ;-), of course you can arrange all the “Text plates” and all the “cableTie” parts on a separate buildplate and go from there, that is your choice.Important; for the “Cabletie” Parts, due to sometimes small...

Added a photo showing the Endstop in fluorescent green filament. Print Settings Printer: Woodstock Delta Rafts: No Resolution: 0.2mm Infill: 25% Gyroid Filament: Generic PLA, PETG Any Notes: Orientation is often not correct, you will most likely...

Printed Parts Assembly Mount pt 1 Assembly Mount pt 2 Backer Plate Bearing Filler 3to5mm X 2 Spur Gear11 Spur Gear21 Switch Plate Hardware Bearing: 5mm ID, 10mm OD, 4mm thick X 2 2.5mm x 14mm Cap Screw X 10 2.5mm x 35mm Cap Screw X 7 2.5mm Nuts X 8...

This is a ventilation system for an IKEA Lack enclosure.The top and bottom flanges have a “key” that will align the two halves so that the screw holes line up as well as the notch that can be used for servo and/or fan cable management if you wish to...

... post 'em! Really! Take a cameraphone photo with your dope color matched mount in all its glory and show it off! Plus it really helps get this design out there to the world.Want a generic GoPro mount version?I got you covered, check out this design.

Note that the Base Plate was not countersunk in the model for ease of printing and to allow the user to choose the fastener style. Bill Of Materials: (1) Mount Rev0 (1) Base Plate Rev0 (1) Adapter Spacer Rev0 (1) Holder (4) M3x20 Steel...

6 is a hinged version, you need to print 3 of the hinges and 2 of the shafts.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my other designs:https://www.thingiverse.com/thing:4654378 - Rivet Cutting...

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

In a pinch (if your printer has issues printing these tiny bastards), you might be able to get away with some clipped up bits of the unused horns included with your servos. I designed the junction of two shoulder pieces to be held by two 3mm x 6mm...

This is mainly composed by Nitrogen (98%) it is 1.45 times the pressure of that of Earth at the surface, and it is 1.19 times more massive. Titan atmosphere has a climate system, in which methane sublimate and form clouds. It is known that Titan has...

... for personal use only, non-commercial, not for resale! You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints/builds of the model. ... Instagram: https://instagram.com/srheuropecom?utm_medium=copy_link

Happy printing and happy gaming! And of course there's lore to go with this; it wouldn't be me without it: The Landshark Grav Tank is another product of the labors of Belisarius Cawl and his faction within the Adeptus Mechanicus. Intended to fill...

40x55mm.you need 2 pieces of rubber band, wire or tape.you need 1 piece of Periscope tube 01 or standard 32mm PVC tube.(Periscope tube 01 89mm long results in a Periscope in/out of 150mm)But you can also use standard 32mm PVC pipe to get a larger...

The LED-tube itself is printed from transparent plastic. Feel free to install a lipo and a step-up-converter or whatever you want ... There are three versions of the body, for - arnuino nano - node-esp8266 development boards - 49 x 26 mm -...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

[7] Thing Title : Tweezers (single print) Type 1 Simonwlchan created a set of precision tweezers, made available under Creative Commons - Attribution on thingiverse.com. [7] Thing URL : http://www.thingiverse.com/thing:1081911 Find the detailed...

Other Notes: I printed these on a Super Racer @ 100% infill, 100m/s 210/60deg. I wanted them solid to transfer as much of the vibration as possible through to the pedal. Probably doesn't need to be that solid but they still took less than 1 hour for...

You can automate it by printing this gearbox that will snap into the mechnisim.I have been successful at driving it with plastic 9g servos after modifying it to be 360. I highly recommand using metal gears which I plan on doing as I already had lost...

this should be intuitive ISSUE ADDRESSED 1 OF 3, The manufacturer claims a print area of 240mm x 290mm. (I don't think I was getting even that!), but more could be squeezed out with alternate parts The issue is with the wheels that are mounted to...

Summary: This is a WIP (work in progress), so don't expect me to answer question about how to print things. If you need different file types let me know and I'll see what I can do. I'm just a hobbyist and I'm always learning. ...

Please ensure that this part will fit before printing. May require some tweaking. Results will vary.) ~4 In. flap ~Flap joint Optional parts: ~4 In. coupler Things you will need to purchase: ~4 In. duct fan...

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...