3d printed camera stand

Triple 360 Camera Stand Prototype Unveiled, Fails to Meet Cost Requirements Conceived to harness the power of three RICOH Theta 360 cameras, this innovative stand unfortunately stalled during its prototype phase due to manufacturing challenges that...

To assemble this stand, you'll need: 1 x Raspberry Pi Camera 1 x Camera FFC (Flexible Flat Cable) 4 x M2 6mm Socket Cap Screws 4 x M3 25mm Socket Cap Screws 2 x M3 30mm Socket Cap Screws 6 x M3 Hex nuts An optional cork base is available to protect...

‣ PRINT&PLUG stand for any YI Home Camera ‣ Perfectly fit the original YI charger ‣ 2 degree of freedom : • horizontal orientation • vertical orientation ‣ 2x1.5mm screw suited for : • https://www.yitechnology.com/yi-home-20 •...

However, it needed a stand to lift it up so it could see my print bed clearly. The camera comes with a keyed base for attaching to the mounting plate, but I didn't need to attach it since I was using it as is. ...To ensure proper pan function, I added...

This is a simple and useful stand for a YI Dome indoor camera (may be compatible with other models as well) to incline it (useful if it's in a place where it can't see the floor). Easy and fast print, room for cable. ...For additional stability, add...

My phone has a large camera bump and this stand accounts for that using a cutout however the dimensions used will work for lots of different devices. ... printed on a prusa mini not MK3s just there is no option for mini on thingiverse for some reason.

CCD 30 FPV Camera Stand: Capturing the Action from Every Angle

A simple wall mounted stand for your SimpliSafe Indoor Camera. ...Attached to wall with command strips.

Print Settings Printer: DIY + Mendel90 Rafts: No Supports: No Resolution: 0.25/0.3mm Infill: 15-20% Notes: You'll need 2x whichever stand option you choose for each Pi and 1x camera mount. Printed at 0.3mm layer height @ 0.54mm extrusion width for...

I made a couple change: 1) Made the actual stand taller 2) I made the base wider and added hollow circles (I paused the print job and added washers to the print, so it was inside the print when done) - I did this add weight to the base. ... **Note for...

This is a versatile stand with rear cover for the Raspberry Pi camera and HDMI module. This is based on @freto's case for the camera and HDMI board so use the front cover and replace the back cover. You will need one M3x25 bolt and a nut - although...

Xiaomi camera stand ET4 - No more fiddling with screws, just install it using the printer's mounting holes.

... less? To implement this solution, you'll need to have the original PS Camera stand on hand, along with the printed base. ...You can choose between printing either Holder A or Holder B, or both, depending on your specific needs and preferences.

A 120mm tall stand for the Kasa brand pan and tilt camera. It took about 10 hours to print with a 0.6mm nozzle and 0.28mm layer height. ...It's a pretty simple shape though, so nozzle size and layer height probably aren't super critical.

You will need one M3X1.25, I used the longest one I can find to make sure that the two connecters fit on the bolt, as well as 4 M8X16 or longer for the camera case and 4-6 M8X12 to fit the printed parts together, and as many M8 nuts as you used. The...

A desktop stand for the Raspberry Pi Camera. Features an enclosed case to keep out dust and a path for the camera's FFC to run under the stand and out the back. Optional cork base to protect the FFC underneath. Print with your favourite...

... iPad on a camera tripod. You can print out this design too! For more information about this project, visit http://eugenweb3.eugenfound.edu.gr/utech. Here are some printing settings: Printer Brand: MakerBot and Printer Model: MakerBot Replicator 2X.

To assemble the stand, you'll need one M3 screw with a nut for the camera mount. The mobile mount requires two additional M3 screws and nuts. The slider parts for the mobilephone must be screwed together at a distance where your phone will fit...

... pi camera mounted onto my Ender 3. ...When I purchased a Prusa I wanted to reuse the camera housing in (https://www.thingiverse.com/thing:2886101/files), which has been reliable. I designed this camera stand to work with the same camera housing.

ENG : Stand for the camera to film in a lower direction when it's placed on furniture. ... Angle = 12.5deg Height in the middle ~ 43mm FR : Pied de caméra pour pouvoir filmer plus bas lorsqu'elle est posée sur le haut d'un meuble Files : STL...

The tripod mount and circular outer case on the bottom of the Paillard Bolex 16mm camera makes it hard to stand on a table in a secure way. This is especially difficult if there are heavy lenses on the camera. This stand is designed to support the...

I'm a Text Rewriting Bot. ...Let me rewrite this for you. Minimal Stand for Raspberry Pi Camera Watch at your convenience by visiting http://youtu.be/qpCJsqS9gb8

... such as cylindrical projection. The stand itself is made from PLA plastic, printed in black for the top and bottom, with natural clear used for the connecting piece - a clever design choice that minimizes visual distractions in 360-degree photos.

Because my initial setup only featured a 15cm Raspi cam cable, I adapted the excellent camera mount from *prodal* and developed this customized camera stand attachment. It seamlessly integrates into the three pre-existing holes of the original...

The stand has provision for a charging cable and does not obscure the screen area.There are many apps that turn an iPad (or iPhone) into a remote camera. ...Alfred is perhaps the most well known https://alfred.camera/ though I have no connection with...

A small stand for (Amazon) Blink Outdoor cameras (BCM00400U). - Compact design. - Notch on front of riser allows camera to be angled downward. - Uses OEM mount and screws, and provides stable feet. - Feet are not visible to camera, in any...

A small stand for (Amazon) Blink Outdoor cameras (BCM00400U). - Compact design. - Notch on front of riser allows camera to be angled downward. - Uses OEM mount and screws, and provides stable feet. - Feet are not visible to camera, in any position. ...-...

DJI Ronin / camera stand adapter Convenient to quickly change from ronin to tripod. The model is a little tight, just heat a little in the hair dryer to fit perfectly to the ronin stand. ... You can put a screw on the adapter to fix the ronin stand.

I needed to create my own camera stands from scratch, so I started by crafting a sturdy screw attachment that would serve as the foundation for my custom stand. ...With this attachment in place, I can now build a personalized stand around it.

Hence why i designed and printed this " stand/ Holder“ It allows you to uses the camera physically independent of your phone or tablet device. Note: a good quality USB-C extension cable and or the appropriate high quality ; video capable USB-C...