3d printed bit holder

I printed it with white PLA and have no problems after about 12 months, even though we had already nearly 40°C this summer. The holes have a diameter of 6 mm, so you can use M6 threaded rods. The length can be controlled by the number of levels.</p>...

Although it doesn't have chamfered edges and the bottom guides are not angled, the print fits well onto the carriage remix from tximy. The holding tab at the top may still need some adjustment but I need to finish building the carriage and see how...

CAUTION** This revision is also untested, but it fits better than R2.\r\nAdded R1 for a MKS GEN L Board, which is tested now.\r\nPlease provide feedback if you print these parts to help me improve them.\r\n\r\nStep files are included so people can...

# Ultimate Drawer System Designed to be the ultimate drawer system that is * printable with FDM printing * optimizable for anything you store in drawers * compatible with Thingiverse's Customizer * backwards-compatible with MarcElbichon's Ultimate...

1) Print this out 2) Pull off the spray nozzle on your bottle of hairspray 3) Snap this into place 4) ... 5) You're done! Now, I have a little sheet of paper towel folded next to the can, and every time I want to apply some hairspray to the bed...

The Stem-mount parametric model didn't produce flat sides with larger stem sizes which made it hard to print. I've updated the .f3d file so it forces flat sides. I've included two properly parameterized Fusion360 f3d models so anyone can now create...

The kit itself includes: Front barrel extension (3 individual parts) Stock attachment piece (1 single part) Shoulder stock connector (1 singular part) Shoulder stock (3 separate pieces) Handle (1 individual part) Rifle scope (4 distinct components)...

Human: Gameplay Video - https://youtu.be/oej_kcawIRE Parts: (6) - m5 x 30mm Bolts (6) - m5 Hex Flange Nuts (6.5") - 1/2" PVC SoftTouch Self-Stick Non-Slip Surface Grip Pads - (6 pieces), 1" x 4" Strip - Black...

I was thinking of printing JT3D's Affordable Rock Tumbler but wanted a little more control so I decided to build one based on an Arduino. The main thing is the stepper motor and using its rpm and steps/revolution to get an approximation for how long...

So instead, I printed a separate case. Not completely satisfied with the 4 part case design, I also made a matching bottom for my case to make it easier to wire everything up. Now there are even more options. I changed out nearly every part of my...

The 'heatmap' image I'm showing is just one I did a print screen from the internet - the quality isn't great, and I'm not sure of the size since I don't use topographical mapping myself. The probe points may not match the exact locations on the bed,...

... The clips should move smoothly otherwise they will not grip the eyepiece very well. These were printed with support, but designed to work without it. If you encounter any issues, please let me know. ... Arsenal's website is arsenaLproducts.com

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

... so I installed three spacers. His desk is now rock solid. It actually worked out pretty well.Print SettingsPrinter Brand:CrealityPrinter: Ender 5Rafts:NoSupports: NoResolution:.16mmInfill: 100%Filament: Overture PETG White   Category: Office

Added on October 29th: CSS Charleston CSS Chicora CSS Colombia CSS Huntsville CSS Louisiana CSS Mississippi CSS Missouri CSS Muscogee Added on November 2nd: CSS North Carolina CSS Raleigh CSS Richmond CSS Savannah Updated on November 12th: Converted...

Since the housing is hollow when printed with infill, it might tend to swim. So I recommend to drill some small holes in the outer shell to use the infill space for ballast water... The shaft should be 10mm in diameter and ca. 80mm long and made...

If you want to print the most cannon as possible, choose the normal models.I made also a "flat arrakis" or "board" version using the entire topography.The file's names explained: name_1_x_10_y.stl is 1 : x* 10^y. So _1_6_10_7 is 1:600000000 or one in...

Threads of diameters between 3mm and 10mm have been successfully printed, but you can use any diameter for your designs. Thread shapes are similar to ISO METRIC standards but not identical. Initial tests using screws and nuts from this library...

Print the surfaces 6mm thick. ...50% infill PETG This chain roller fits a lot of Yamaha Dirt Bikes and ATV's: Part # 30X-22178-00-00 Yamaha Motorcycle 2009 WR250F - WR250FY Frame Yamaha Motorcycle 2013 WR250R - WR25RDC Frame Yamaha...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

Notes: Parts to print: 2x middle, 2x center, 2x center (contains mega x) 4x side, 4x corner Start mounting the middle parts using the original short screws. Once they are fitted you can easily snap in the other parts. To use the corner drawer...

This print took me about 17hrs on my Creality CR6-SE as I wanted it to be super solid and smooth. This palette is made to fit a 3-layer storage container from walmart...

You like this print? Maybe have a look at my other designs as well: Link: https://www.thingiverse.com/lexx3d/designs ----- Deutsche Version ----- Ich mag fummelige Sachen nicht und einen Zylinder in 2 Ringe wie bei den meisten Haltern zu...

A massive project undertaken by my tabletop group to play BattleTech, which faced challenges with both printed maps and hex-sheet setups due to persistent forgetfulness of terrain and later issues with terrain pieces getting knocked around on the...

If you fix it for print, make a Remix, or send me a model for re-upload it\n\nA seductress is a supernatural entity in folklore (traced back to medieval legend), that appears in dreams and takes the form of a woman in order to seduce men, usually...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...

Furthermore, I provide a test part called "PSUCoverDummy_AllVersions," which you can print and try the fan dummies. You can get the fan dummies here: Fan Dummies On the cover are the names: * 90 = normal 92 mm version * 90R = for the 92 mm rotated...

I printed the body and other parts, mounted the sensor in the sensor mount then glued the parts in place. As for the missing parts, get these from the original design that I remixed this from. ... Link to downloads for motioneyeos:...

If you can repair it for printing, make a Remix, or send me a new model to re-upload it. Easter Island, known as Rapa Nui in the native language and Spanish: Isla de Pascua, is a Chilean island located in the southeastern Pacific Ocean at the...

... after which the vice fastening screws are tightened. The photo shows the template of the first version. The files have not been modified much based on the results of use. I didn't print them. ... If you have any comments write in the reviews.