3d printed ball marker

This remix fixes the height issues of the original (too much Z space, golf ball would rattle around). I have also added press-fit slots for 4 8x3mm magnets which hold the two halves together while drawing in the stencil. Just print 2 of the main...

This remix fixes the height issues of the original (too much Z space, golf ball would rattle around). I have also added press-fit slots for 4 8x3mm magnets which hold the two halves together while drawing in the stencil. Just print 2 of the main...

To create it, I used Customizer, an interactive web application that allows designers to modify parameters like letter height, letter style, model rotation, spike height, marker diameter, and initial inscriptions. The details are as follows: ...

Marked to indicate timing on a ball for a Table Tennis Timekeeper.

... material, allowing the model to freely sit on the print surface. For in-depth details regarding this particular project and how-to information, navigate your browser to the dedicated page: http://www.instructables.com/id/3D-Printed-Ping-Pong-Ball/

I was after an easier to print version of KawClerics great looking goal markers. I'm sure the origionals look better but my garage is cold this time of year and printing anything with that level of detail becomes a bit of challenge! This is the main...

I thinned the walls to 2mm for easier marking. ...Use sharpie ultra thin marker. ...I personally used a Brim to keep it secured to the bed.

... Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=58641 Using these options: Spike height = 6 Marker diameter = 16 Letter height = 13 Initials = EMK Flip model to = 90 Letter type = italic

Marker Initials You can customize this marker using the options below: Flip model to: - 90 - 135 - 180 Spike height: - 1 mm - 3 mm - 5 mm - 10 mm Letter height: - 6 in (15 cm) - 8 in (20 cm) - 10 in (25 cm) Letter style: - Simple - Bold - Italic -...

Marker Diameter: At 15, the diameter is just right for writing and drawing. Spike Height: With a height of 5, it provides precise control over strokes and lines. Letter Height: Elevated to 12, each letter is raised and noticeable. ...Flip Model To:...

Here is a dual extrusion 8-Ball for marking your final shot in APA league play. ... Category: Sport & Outdoors

Instructions Utilizing the following settings: Letter Height: Set at 9 Spike Height: Configured to 5 Flip Model Orientation: Aligned to 180 degrees Letter Style: Default Plain Type Marker Diameter: Fixed at 15 units Custom Initials: Inscribed as...

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58641 Using the following options: initials = NP spike_height = 5 flip_model_to = 180 letter_height = 12 letter_type = plain marker_diameter = 15

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58641 Instructions Using the following options: letter_type = bold marker_diameter = 12 letter_height = 10 flip_model_to = 0 spike_height = 8 initials = JAC

Created with Customizer! ... Using the following options: Flip Model To: 180 degrees Letter Height: 13 mm Initials: RB Spike Height: 5 mm Marker Diameter: 15 mm Letter Style: Fancy

Customized version of Thingiverse Thing #58641 Created with Customizer! ... Instructions Using the following options: Fancy Letter Type at a Height of 12 Set Initials to "Andy" Spike Height at 5 Rotate Model by 180 Marker Diameter at 15

Customized Version of Thingiverse Model #58641 Created with Customizer! ... Instructions Using the Following Options: Marker Diameter: 15 Spike Height: 8 Letter Height: 10 Letter Type: Plain Initials: MBO Flip Model to: 180 Degrees

http://www.thingiverse.com/apps/customizer/run?thing_id=58641 Instructions: Using the Following Settings: Initials: KAR Letter Type: Plain Letters Marker Diameter: 15mm Flip Model to Face Upward: Yes, at a 180-degree angle Spike Height: 5mm Height of...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58641 Instructions Using the following options: letter_type = fancy marker_diameter = 15 flip_model_to = 180 initials = KR letter_height = 12 spike_height = 7

... ...https://www.thingiverse.com/apps/customizer/run?thing_id=58641 Instructions Using the following settings: initials are I G C H marker diameter is 15 flip model to 180 degrees spike height is 5 units letter type is plain letter height is 10

... ...at http://www.thingiverse.com/apps/customizer/run?thing_id=58641. To achieve this, the letter height is set to 13, marker diameter is 15, letter type is plain, initials are RH, and the model was flipped at 180 degrees with a spike height of 5.

... ...Here, the letter height is 13 and spike height is 7, while the model has been flipped to 180 degrees. The letters used are plain, with a marker diameter of 15, and the initials on it read "RH".

... http://www.thingiverse.com/apps/customizer/run?thing_id=58641. To use specific features, set spike height to 5, marker diameter at 15, letter height as 13, input initials as 'CkP', flip the model by 180 degrees, and choose fancy letter style.

Customized Version of a Thingiverse Model Generated with Customizer Tool Instructions to Use This Version: Using the Options Provided: Set Spike Height to Five Units Choose Letter Type as Fancy Script Engrave Initials with J and D Symbols Rotate...

... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58641 Using the following options: Marker Diameter: Set to 15 Letter Type: Changed to Fancy Letters Initials: Entered as DOV Flip Model To: Set to 180 Degrees Spike Height: Set to 5

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58641 Instructions Using the following options: letter_type = plain flip_model_to = 0 spike_height = 7 letter_height = 9 marker_diameter = 16 initials = BCJ

... on Another Website. ... Created with Customizer! Https://Https Www Thingiverse Com Apps Customizer Run?Thing_id=58641 Instructions Using the following options: initials: marker diameter: 15 flip model to: 180 degrees letter type: plain spike height: 5

A customized version of http://www.thingiverse.com/thing:58641 was created using the Customizer app, with specific settings including letter height at 9, marker diameter of 16, plain letter type, spike height at 5, and flipping the model by 180...

Created with Customizer: Customized Version of http://www.thingiverse.com/thing:58641 Instructions Using the following settings: Marker Diameter: 15 Flip Model To: Zero Degree Angle Initials: B.C.J. ...Letter Type: Ornate Font Letter Height: Nine Units...

Thingiverse apps customizer run thing ID 58641 Instructions Using the following settings: spike height is set to 5 units marker diameter is established at 15 units letter height stands tall at 11 units the personalized initials chosen are JEFF font...