3d printed bacon

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

I printed and tested it with four 10 W blue LEDs (450 nm wavelength), but other types and wavelengths can also be used. Using the 10 W LEDs shown here, an 80 mm fan must be mounted to avoid heating the reaction vials above 30 degrees C. If lower...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

There are two methods you can use, either print up a new modified WhiskerScar with the rib cut out for a 19 mm OD and 16mm ID 1.7 mm thickness o ring (or some close equivalent) or you can use electrical or masking tape on an existing Whisker scar...

Various layouts to organize components and tools to keep everything close by so you can make repairs without leaving the table Print instructionsUn pequeño taller para poder trabajar en el salón de tu casa sin quemar nada y teniendo todas las...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

This design fits on a Prusa i3 MK3 bed.Note: Please only attempt this if you already have some experience with soldering, wiring and electronics in general.Note: Some ATX PSU's may be too deep for this design so if your PSU is over 135mm deep it may...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

I figured out the airflow issues and designed this print as one of many modifications I made. Since the case isn't terribly efficient at exchanging ambient air, I created this CPU shroud to prevent hot air from recirculating back into the heatsink. ...I...

Https://www.thingiverse.com/Apps/Customizer/run?thing_id=739573 Instructions: Using The Following Options: Text Outline Strategy For Non-Latin Scripts = bar and glyphs Outer Edge Color Of Design = gray Displayed Name On Model = kanu Frame Width Is...

If you'd like to buy a print of this with metal inserts in the drill holes, please check out my gunbroker page: https://www.gunbroker.com/item/858377600 This is version 1.2 of the C93 paddle release jig I previously released. This updated version...

The box back design for each car is similar in design since I want it to be seen as a set.Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "300ZXBoxBack":1) Start (Colour of the...

I printed it with ABS plastic, but PLA or other materials should work fine as well. To ensure it is strong and not prone to breaking easily on my first prototype, I used 50% infill (and four-layer walls) and might use less if I build another one. I...

Access it here: [http://www.thingiverse.com/apps/customizer/run?thing_id=287025](http://www.thingiverse.com/apps/customizer/run?thing_id=287025) To print this design, set the following options: - grid size: 0.1 - orientation: 1 - pixel shape: 4 -...

There is, however, a fair amount of stuff to print for this modular insert and some optional parts. I will Identify the stuff below that is optional. To start, take everything out of the original base game box, including the manuals, player HP/RAD...

このモデルは以下のモデルの自己Remixとなっています。 CE32A 1" Speaker Driver Enclosure PAM8403-based Tiny Audio Amplifier Board Adafruit Stereo 3.7W Class D Audio Amplifier MAX98306 Enclosure Adafruit Breadboard Friendly 3.5mm Stereo Headphone Jack Enclosure Adafruit USB...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

The filament used is all dark red PETG eSUN brand, printed at 245 ° with bed 80 °, 100% infill to avoid any deformation in the heat. The description is not detailed simply because it is not complicated as a project, certainly a bit of manual...

To achieve the insert as shown, print six of the player trays, two of the resource/silver trays, and one of everything else. The photos show how to layer all the trays, game board, and manuals in the box. ... I have included the original OpenSCAD...

All parts should be printed first. Then the holes are drilled: the hinges with 4mm and the screw holes with 3.5mm. This gives you optimal support and a high degree of accuracy. The brackets are designed for doors with a 2mm distance from the...

This can burn your house down if done incorrectly!Do not attempt to build this unless you are familiar with:SolderingLiIon battery safetyBasic electrical engineeringNow with added STEP file for remixing.Print SettingsPrinter:Modded...

... an STL file. The included STL was created while experimenting with TinkerCAD. It's still very much a work in progress, so suggestions and tips are welcome! Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: Doesn't Matter Supports: No

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

The "printmode = true" with its following variables will prepare a print-ready layout of your parametered Structures. The length of each (not printable) Threaded-Rod will be "echoed" in the OpenSCAD-Console. They can be cut to exact that length. -...

If you don't use your Western Digital MyPassport Pro all the time, but more like once or twice a year as a backup device for your camera, the battery might be damaged through constant drain of stand-by electronics. My last device died of this since...

I printed in PETG, Black, Orange, White. Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held...