3d printable fantasy buildings

In order to use this setup, you will need to perform extensive modifications to your 3d printer. I've tried to detail as much as I can here, but inevitably you will need to work a few things out for yourself. The setup uses the stock Ender 5...

This file you can send to your printer and the tower should be printed out with the different temperature settings. Print instructionsCategory: 3D Printing Tests Summary [2018-03-28] Useri_has_it found out that the only thing to make it work...

Intended for 3D print. Please read product description below. An implacable biomechanical horror capable of both plumbing the depths of the ocean and floating through the air using antigrav suspenders. This model kit contains enough parts to print...

The shims will directly contact the printed part; for that matter the bore diameter for the shoulder bolts has been reduced from 5,5 to 5,1mm (you might drill that out if it does not fit) You will also need all the screws to attach the parts to the...

PLA has an inherent shrinkage factor, and that varies depending the type of PLA you use and all the other many things that go into 3D printing. You may need to adjust your slicer to (every so slightly) enlarge or shrink the part. Z-axis dimensions...

Cómo configurar los parámetros para personalizar la impresión del pomo “silla de montar” 2.1. Para poder personalizar el pomo “silla de montar” deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de un software...

All 3D printed parts are printed in ABS using the Voron standard for printed parts.The files that are uploaded are the files that had to be modified from the Voron design team files in order to adapt the components from the FLSUN CUBE. All other STL...

Loaded up 123Design and exported with coarse tessellation. Loaded up a Raspberry Pi 3 from the 3D Warehouse. (Not an exact model, in turns out later.)</li> <li>Imported the USB and RJ-45 plug caps. Slowly but surely with my micrometer, the actual Pi,...

I tested it out and it seems good, but to stop the weight of the cables plugged into the dock pulling it back I used some Command Strips on the bottom of the dock holder to keep it in place. Bill of MaterialsRequired: 3D printer and filament (inb4...

I was already pretty well dialed in with the openbulilds mods, but this pushes it to the next level. You can source used 20mm taz extrusions here: https://itworks3d.com/product/aluminum-extrusion-20mm/ Development thread here:...

These don't work as well as steel or carbon rollers so they are not a preferred option. You can choose to print the tubes rather than source carbon tubes so I have included STLs for these, there are 3 sizes - the short large diameter tubes are for...

This version also allows for the use of the EVA hotend mounting system which I highly recommend you use. You will need various M3, M4, and M5 hardware. Mostly I will leave that to you as to quantities for right now until the project is fully...

I may do a half-height one in the future, or you can download the fusion model and change the BoxHeight parameter.Containers for Twilight Imperium 4th Edition.While 4th Edition provides a nice, full box insert for the game, the insert is not well...

Most things shouldn't need supports except for the bottom-wall-mount.stl and bracket-top.stl.Non-3D printed components I used:A lot of M3 hex socket screws and nuts of varying lengths (6,8,12,16,20mm). The nuts should be hex, not square</li><li>5...

The input data you provided seems to be a list of tuples, each representing a point in 3D space. The format is as follows: * The first element in the tuple represents the x-coordinate. * The second element represents the y-coordinate. * The third...

I'm no design expert, and 3D modelling makes my brain hurt. However, with a lot of perseverance, a set of calipers, hundreds of edits and redesigns, dozens of test prints, I have made a replacement ring battery.</p><p>You will need the...

The fan ducts from the Mosquito BNB Extruder work with this design (Tested and used by Brad Cronk), I have included the stl for the BS6RHD_Mosquito_Fan_Shroud_5015 in the zip files, you can also click the imbedded link to download it.Category: 3D...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...

Think of it as the gauntlet is laid down and a super fun challenge in 3d spatial orientation! Oh and don't superglue your fingers, eyelids, or other body parts to various things, it's not as fun as it sounds. You may want to try using sticky tape...

The paper was cut to fit over the mask on the 3D-printed back and then held in place using blue painter's tape to hold it in place by the edges. This screen gives a very heavy texture, which reduces resolution somewhat; a thin plastic diffuser sheet...

Note: The G code files are set up to print with PETG material.2) Procure the commercial hardware from the parts list, M3 screws, square nuts, hex nuts, and 4mm OD x 2mm ID Teflon tubing (or re-use the existing buffer tubing).3) Cut the existing 10...

They are both the exact same size... Another Sketchup Model - Debunking the Myth that Sketchup is Useless in 3D Printing Print Settings Printer: Tevo Tarantula Supports: Yes Resolution: 0.2mm Notes: All pieces should be printed in the orientation...

It consists of 3 pieces: - the main box with a solid floor and honeycomb sides (the "bottom" or "box" in UBG terms) - the lid with a honeycomb pattern and large, rounded coinslot from which the tissues emerge (the "top" or "lid" in UBG terms) - a...

&nbsp;To your health!The Salud CO2 Monitor was designed to inform you of your local air quality in terms of CO2, while also featuring a long battery life and simple no-solder assembly.In addition to the three 3d-printed enclosure parts, you will...

*Tubing* In addition to the 3D printed parts, this thing also uses steel tubing * Beam: 1" OD x 11" long * Column: 1.5" OD x 20" long The material I used was 18 gage. Any thickness will probably work but lighter is better. Maybe. *Steel Plate* ...

This steering wheel is a remix from this https://www.thingiverse.com/thing:4058270I designed almost every parts in Fusion 360, the only files used from the parent are the handles.The plate can be 3D printed but on my design it was a carbon plate, i...

If not, here is a good pair you can buy (local hardware store is the best option):...

Each Skittle knocked down equals one point.The first player to reach a score of 101 is the winner.You can make up your own rules.&nbsp;When I have played the game with my 3D printed set I have found the skittles nearest the post are difficult to hit...

Here are the parts (top down): Antenna Head Visor Eyes (2) Teeth Body, upper Body, lower Door Arm segment, shoulder (2) Arm segment, short (10)* Hand (2) Leg segment, hip (2) Leg segment, short (8)* Leg segment, ankle (2) Foot (2) Stand Also...

I used an Igus one i bought for another project a few years back, so i don't have a part number for that one, but you should be able to make most of them fit. You will need 6 M3 heat set inserts ( http://www.mcmaster.com/#catalog/119/3267/=zw8u0v) ,...