3d print worm

... the placement of the board mount is perfect, but my guess is it should be close. Print this and take your holy hand grenade to the next level. ...10 secs 10s Sound Voice Audio Recordable Recorder Module Chip for Card New http://r.ebay.com/Heh99k

Print all the pieces with supports, with 3 or 4 bottom/top layers and 25% or so infill. The roller ends were made slightly too large. File them down evenly until the roller fits in the indents in the sides of the cartridge and spins freely. A little...

I use this: Amazon link Some cable connector like this: Amazon link If You enjoyed this project and You want to say "Thank You" please consider supporting me by sending a tip on thingiverse or my PayPal here. I hope you enjoy it! Print Settings...

The dustshoe has a total of 5 parts that easily can be printed in three parts or maybe even less. It contains: A base part called Dustshoe basis (with the version on the end) Then a part to attach to your vacuum cleaner called Dustshoe...

Changes I made to existing models: * Removed cable tie bump things because they're unnecessary and just add to print time. * Added holes on the Raspberry Pi panel so you can zip-tie extra Z cables in a service loop. * Changed the PSU front panel to...

... so I installed three spacers. His desk is now rock solid. It actually worked out pretty well.Print SettingsPrinter Brand:CrealityPrinter: Ender 5Rafts:NoSupports: NoResolution:.16mmInfill: 100%Filament: Overture PETG White   Category: Office

All prints must be made with a filling of not less than 80%. The knobs are available in 2 versions, one with the predisposition of the recess of the 6mm nut for the M3 screw the other to be threaded later with an M3 male. Obviously, use this...

Print quality is good, and I'll try a benchy and ghosting test later. The diameter of the sticks is 7.2 mm, but sticks with a diameter of 11 mm can also be used - they're almost three times as stiff in theory. 7 mm glue-sticks are fairly cheap, and...

4.) Time to choose colors for printing. Going all lime green, it looked nice because I thought this vibrant tone brought a certain brightness when laid on a dark or otherwise subdued backdrop which always helps capture attention wherever applied...

FederationDN-V2-ship-stls.zip – Print-ready combined ship STL files. This kit supports the following variant ship classes: Federation class dreadnought The original TOS-era three-nacelle dreadnought from Franz Joseph’s 1975 Starfleet Technical...

It's a simple print but does require your printer be well tuned. I had to remake this idea about 6 times before finding something that would fit right and not touch the heat block. You will need to remove the H2 from the printer in order to...

The clips are printed from PLA with a thickness of 6 mm. Each strip has 3 clips. The heat pump has an outlet diameter of 500 mm (1960 cm^2). The wooden casing with applied strips has an outflow of 2 x 14 x 475 x 20 mm (2660 cm^2) plus 36%, so more...

- Some nice, yellow PLA (I couldn't find an exact color match, but I got close!) - Revel Contacta glue - A hot glue gun - Some clamps - A soldering iron (with a small tip) & solder - A small, flat-head screwdriver - [Male & female USB C...

I made it to test the ball joint and see if it is fun to play with. It's not supposed to look good,don't print this! List of mix n match animals Crocodile: https://www.thingiverse.com/thing:4751955 Minecraft Steve:...

Stylized Earth Python Generator is a Cinema 4D scene that enables quick creation of a unique representation of Earth by leveraging inspiration from dot matrix printing. Instead of ink dots, elements are created with mesh that wrap around a sphere. In...

Here's what you need to print:Big Box - primary gameplay components1x Map Tiles1x Features1x Missions5x Agencies x54x Joint Ventures x41x Outcomes1x Time1x Points1x CalendarsFirst Small Box - Advancements and Planetary Samples1x...

There is also an experimental EDF holder, not even printed it yet, that would attach to the Body Lid or anything else. The base can be fitted and the two parts glued together. Just an idea but worth putting here. Again saw a Flite test plane with...

The pieces can be assembled in multiple different ways.  - Alien Desert bases: 19 different bases ranging from 30mm to 80mm, and including a desert rock scenery piece.  All the parts are pre-supported for SLA resin printing! Storyline of the...

Details include: - `custom_top_outer_edge_chamfer_radius = .6`: defines an extra smooth curve outside all traces including ports which might contribute slightly higher price compared purely printed solutions depending supplier agreements currently...

Additionally it was printed just out of PLA. you might get even bigger strenght with more perimeters or other materials WARNING:This hook is designed with mooring and releasing some light wight gear in mind. DO NOT use it for climbing or in cases...

... Fusion 360 file is included. I apologize, it is a bit sloppily modeled but the project was initially created to just model and print some test-fit bits for the entire project and ended up encompassing the whole thing. ... Hope you find it useful!

To taper this wing just print the airfoils smaller and smaller to give the taper. So to reduce chord to 50% is easy. When you resize in a slicer it will tell you the length of the chord. So you just need to reduce this by typing the new value into...

... for the cost of a pair of 120mm silent computer fans, you can have a silent B1! Oh, and it is so quiet now. All you hear is the fans on the head and the steppers when they move at high speed. :)I printed this on a BIQU B1 using eSUN PLA+ filament.

More suggestions==================== I recommend printing the socket adapter and the snap style arm in ABS for proper flexibility/operation. PLA may be too stiff for them to work well. Also, depending on your setup you may want to use a brim on the...

... let me know in the comments! Printer: Flux Delta Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 80% Post-Printing I designed this using OpenSCAD, and it was a total pain! ...I'm going to have to learn SketchUp or something one of these days....

Print all 3 sizes of each part. 2. Sand the barrel and rail supports wherever they will make contact with the barrel shroud, tank, and scope rail. I used 600 grit. Wipe the parts clean. 3. Install the shortest rail support. It should require...

While I haven't printed it myself, it should work just fine. *** 9/27/18 *** The main litho no longer needs to be resized (I've renamed it to MainMashup.stl). The crown's orientation has been fixed, and all the parts should fit nicely together now....

The tiles were printed with natural PLA, and then welded with their bases using dichloromethane. They were washed and primed in black using Vallejo black primer through an airbrush. A watered mixture of a white craft paint, Vallejo Light Brown and...

we should be able to read the block now success = nfc.mifareclassic_ReadDataBlock(currentblock, data); if (!success) { PLAY_ERROR; return; } // Read successful for(int i=0;data[i]>0;i++) { if(data[i]=='') { Keyboard.press(KEY_LEFT_SHIFT);...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...