3d print stethoscope

This is due to the different number of teeth in the printed gears for each axis. Feed rate changes the speed of the motors. Be careful to not move the azimuth axis too far so the stepper motor wire connected to the motor for the altitude axis...

The measurement is relative to the height it extends above the surface of the badge.[background color] and [foreground color]These dropdown boxes change the colour of the badge background and the contrast colour which effects the border , logo and...

for parts look at the parts list PDF that can be found in the FGC-68 starter kit to actually see how to do it whats this link.https://youtu.be/M_1AAlgVm-4 some tips disassemble the FGC68https://www.youtube.com/watch?v=pDRv5jwRReA a introduction to...

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

Projekt DIY: Wetterstation BMP280 Luftdrucksensor + Temperatursensor, kalibriertes Barometer, I2C, SPI für Arduino, Raspberry Pi Oblique-Unique 20 Mini Magnete - NEODYM - ultrastark - 6x3mm - Original Hall Effekt KY-003 Magnetisches Sensormodul DC 5V...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

You will need: - 3 batteries Li-Ion 18650 - 1 fan : https://fr.aliexpress.com/item/1005003098017287.html?spm=a2g0o.order_list.0.0.3c605e5bUydQEI&gatewayAdapt=glo2fra - 1 Activated carbon filter (to be cut to 80x80mm):...

Printing Select the vertebrae that you need and import them into your slicer. You will need to apply supports to the bony parts that stick out the back and to the sides. IMPORTANT: Be sure to label the vertebrae as they come off the printer! ...

This is a thing I call the Sand Raker, it is a very peaceful print when finished and put together. https://www.youtube.com/shorts/fRqaw5RR5FI A kinetic sand piece that rotates via an electric motor with a pinion gear of 11mm, and rakes the...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

Just put the LEDs and alarm speaker in a box with a labeled side (printed in white filament) and attach it to power supply fan connector... there is even a slot in my power supply cover to allow the wire to be slipped into (and out of) the power...

There are also two variants of each model - one "basic" variant, and one variant that has been slightly altered to suit printing at 28mm scale. You will find all 28mm variants in the zip archive named "28mm versions" included in the purchase. All...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

If you want to use Anet's original M5 screws/t-nuts, just print the parts with 100% infill and drill out the mounting holes with 5.0 or better yet, 5.5mm (to give you some alignment room) drill. Edit: Full screw list, as requested: * 10pcs of 412...

... done, carefully install your Pi in the bracket, being careful with the pins and make sure all 5 pins go smoothly into the Einsy board. Click the Pi in place so the four printed posts in the corners are flush withe Pi's PCB. ...Snap the cover on.

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

... soon. For those of you thinking about supporting us on Patreon, our patrons get special access to our entire back catalog, including the Meepleverse stuff (not to mention license options to sell printed versions of our designs). ... Happy holidays!

Note: This will decrease your print height slightly! The CR-10S Pro struggles even more than the CR-10 series when it comes to Z motors going out of sync on power off. This is due to the same design as the one used by hoegee, but it works perfectly...

Using it I created 12v powered Media centre with LibreElec running KODI so that I could watch TV-shows or movies in my RV without having to bring disks with me or have access to streaming services. I load the HD up with my ripped DVD's and then just...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

Screw or push inserts would probably also work after drilling the holes to the required size for these inserts (no guarentee) - 5x M3x5mm allen head set screw ###Printed parts - 1x Base - 1x Stepper_Housing **(requires support)** - 2x Front_Wheel -...

The two `o_ring` files are optional o-rings you could print with flex filament. Better to use o-rings, and at a pinch you can probably get away with using a rubber band, or just pushing everything together and putting up with water splashing...

Parts are not oriented for printing. The STEP file is included for easy remixing. I am not an electronics expert but I did the best I could with the design, but still make this at your own risk and let me know if you see something that can be...

####Broom stick section: First test the printing tolerances by assembling only the left, right and release part. Insert the clippart of the wheel section. You might have to grind/cut a little bit on the parts for a smooth fit. Push in the Insert...

The new mount plate prints easier. The new mount plate has better wiring management. The new mount plate allows for a small 8x8 heat sink to be adhered to the back of the Huvud board to cool the stepper driver on the reverse side. The new Huvud...

All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use 220x220 - you need literally for a couple of parts to minimize support. Assembly video: 1)...

Update Added MKII style carriage STLs & source design files. Need the following additional parts (1) McMaster 5233T84 - 3 x 19mm O-Ring (1) M6 Nyloc Nut (1) M6 x 55mm BHCS (2) 606 Bearings Updated Design Change Log - 12-04-2011 -Updated Spindle...

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...