3d print stamp

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

Happy printing and happy gaming! And of course there's lore to go with this; it wouldn't be me without it: The Landshark Grav Tank is another product of the labors of Belisarius Cawl and his faction within the Adeptus Mechanicus. Intended to fill...

I printed in PETG, Black, Orange, White. Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held...

I also don't notice any difference with no polyfill filling at all; so I provided new tops with no basket.* After printing and listening to guppyk2's 4" back horn speaker enclosure, which left me wondering why his design is so popular, I was thinking...

You may have to warm the rear Pipe Sockets a bit as you put the 8mm Pipe in, but depending on your printer, it'll just fit "Snugly", whereas 7mm Pipe will be a touch loose until you tighten down your bolts/nuts.Seriously, use PLA+ (PLUS) filament...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

Messuhr 20mm ******************************************************Update 16.10.2022Das Update beinhaltet 4 neue Dateien.Messuhr 20mm 05(16)-Skala (durch die Anregung des Makes von CHAOSXSPIRITMessuhr 20mm 05(16)-Gehäuse 2 mit verlängertem...

Once I print some more of this I will keep tweaking it - and look to finish meshing a magazine. Nov 29, 2019 Part 2 - YEEUH. HUGE update! I've found a way around a lot of the hard stops of the limitations of space and dimensions, but still...

Various layouts to organize components and tools to keep everything close by so you can make repairs without leaving the table Print instructionsUn pequeño taller para poder trabajar en el salón de tu casa sin quemar nada y teniendo todas las...

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

Access it here: [http://www.thingiverse.com/apps/customizer/run?thing_id=287025](http://www.thingiverse.com/apps/customizer/run?thing_id=287025) To print this design, set the following options: - grid size: 0.1 - orientation: 1 - pixel shape: 4 -...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

Buck Converter (to power my 12v cooling fans) Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so...

Printing of a second prototype is in the works. 2. Centrifugal wheel friction. If the wheel spins free and touches surrounding parts it can "weld". This can be prevented by a very careful alignment of the impeller so that it doesn't touch the...

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...

Here's what you need: * 6m GT2 with 2mm pitch belts * 1x 1040mm closed-loop belt (520mm perimeter) used for dual Z * 2 x 200mm closed-loop belts (100mm perimeter) * 4 x 20-tooth idler pulley with 5mm inside * 2 x 20-toothless idler pulley with 5mm...

Plastic parts printed in PETG, layer 0.2mm, walls/top/bottom 1.2mm, infill 40%. With good part cooling supports are required only for the lower groove of the tool holders. Development log: 04/09/2023 Working sample 04/10/2029 "Head"...

First, you'll need a 2 gallon bucket (I got one from Home Depot for a few bucks), some M5 screws and some M5 knurled brass threaded inserts (use a soldering iron to install in plastic).I also included a strap mount so I didn't have to carry the ICM...

The secondary goal was to keep it simple and quick to print.The tripod consists of the following components:Tripod Head: Featuring fixed holes positioned at 20 degrees from the central axis.Telescopic Legs: Made from 6mm outer diameter and 4mm inner...

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

K40 Paint Rack I recently started painting sla printed miniatures. Soon a lot of 25mm paint flasks crowded my workspace. So I was in need of some paint rack. I searched thingiverse but found none that appeals to me and whose parts will fit in my K40...

Here is an example of how you could extract and print these lists in a Python script: ```python import json # Assuming that the provided JSON string is in a variable called 'json_str' json_str =...

Create solid lines from the bottom of the arcs at the top corners to the top of the diagonal lines at the bottom corners. Design Choices:To construct this paperclip, we created dimensions on graph paper, twice the size of how it will actually...

This design is intended to be a relatively affordable, simple and easy to print electronics project. Remix as required to add a secondary sensor, extra valves, etc. I have uploaded the most current Parasolid assembly file so feel free to dive into...

I encourage experimentation with springs and perhaps with print settings if you know what you're doing to create a blaster fine-tuned to your needs. Grab your Snakethanhas here: https://www.thingiverse.com/thing:3890229 Feedback is very much...

Note: This will decrease your print height slightly! The CR-10S Pro struggles even more than the CR-10 series when it comes to Z motors going out of sync on power off. This is due to the same design as the one used by hoegee, but it works perfectly...

* The final touch was designing and printing a small adapter for a power socket (similar to this one) I happened to have. * I drilled 5 small holes in the back of my tablet, fixed the power socket there using my adapter, and soldered the wires...

... It was only off .13mm (.0051 inches) at the most, but not really an issue if you have printed the parts already. Here is very short video of this machine working. https://youtu.be/HgV3grxkY44 I also added optional **CantileverStablizer.stl**.

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

You might want to widen the holes for the screws with a drill (depending on the printing quality you select). 3. Before assembling anything to the case, use a blow torch to warm up the screw brackets and screw in the screws to gently form a thread...