3d print retainer

Hoover UH70120 Hose Retainer by RebelTaz The retaining piece that holds the hose in and releases it so you can use the wand extensions broke on our Hoover UH70120 vacuum cleaner. I whipped this up in FreeCAD and printed it in ABS-like resin. It has...

I made this a long time ago in tinker cad as an early effort in 3d printing. Its the engagement side for those pressed metal garden gate latches that you see everywhere (in the UK). The problem is they are usually not very good, however this...

Wire retainer for CR6SE to prevent the wire from disconnected accidentally Print wire 1 = 5 mins print, Fast, No support needed ( 0.2 resolution ) Print wire 2 = 38 mins print, slow, support needed ( 0.12 resolution, printed as seen on the picture...

Wire retainer for CR6SE to prevent the wire from disconnected accidentally Print wire 1 = 5 mins print, Fast, No support needed ( 0.2 resolution ) Print wire 2 = 38 mins print, slow, support needed ( 0.12 resolution, print as seen on the picture for...

... like NylonX or Prusament PCCF. After printing, the retainer is designed to be epoxied (use a high-temp epoxy like JB-Weld) to both the motor mount tube and the aft centering ring of your rocket, and is compatible with all major tubing brands.

Usage To store filament Slide the filament through the guide Wrap filament around the spool once over the clip Wrap around a second time and Insert filament into friction catch To print with filament Pull filament out of friction catch Leave filament...

Usage To store filament Slide the filament through the guide Wrap filament around the spool once over the clip Wrap around a second time and Insert filament into friction catch To print with filament Pull filament out of friction catch Leave filament...

When printing the design, it's recommended to do so without any support structures, as they are not required; instead, use only a skirt for the print bed. ...Printing at an infill percentage of 20% and a speed of 60 mm/s yields a completion time of...

Luckily someone had a spare one, but I immediately started thinking about creating a 3D printed extra. It should be plenty strong for most applications, but use your brain (if you are SUPping jaws, please don't use it and blame me). I created two...

This is the retaining clip part of the W4 Veneta hinged door retainer for motorhomes and caravans. It is the part that breaks when the wind catches the door and smashes against the retainer. The original retainer comes in 4 parts. This part fits...

Retainer clip for 5mm fitting core, thickness is 1.5mm

Mini blinds secure their position with a sturdy retaining clip.

Upper spring retainer for 1/10 traxxas shocks

Retainer clip designed to hold electric outlets in place

9004 HB1 Bulb retainer for F 250 188-1991

Rocket Motor Retainer for 38mm Aerotech and Cessaroni motors.

UV Lamp Retainer for T5 4P-SE Lamps

Longer retainer handle. ...Two Trees Sapphire Hottend ptfe fitting is not very handy to install regular retainer.

... for my harbor freight generator. ... Replaces the retainer ring for the circuit breaker weather seal that cracked and fell off. Probably fit other makes and models of generators. Printed with TPU. ... No supports if printed with lip side down on bed.

This is the connection position assurance retainer from a molex mx150 series connectosr with CPA. I broke the CPA clip on my connector so I modeled a new one and printed with PETG. PETG likely must be used for pliability. Print on side. 0.12mm layer...

This fixes that problem. Print instructionsMust print with supports. I recommend printing upside down (hole up, arms down) so that the prints looks nice, but printing it the other way will require less support material. Printed at 0.2mm with...

... you may not need one of these, but the catches seem to be working for me so far. The pictures show one of the catches both with and without the retainer in place (of course, you'll want to print two retainers, one for each catch on your canister).

... Ninjaflex, which offered an elasticity remarkably close to the original retainer's feel. Printing multiple units at once allows each part sufficient time to cool, especially for the last 5-10 layers where temperatures can fluctuate significantly.

This uses the screw in the center of the wallplate (you'll need a longer screw to hold the plate to the wall to account for the retainer bracket thickness), but other than that nothing else needed. ...Since printing the one in the picture I changed the...

... The original retainer features tabs that click into the metal case, but I felt these were unnecessary and made the design and printing process more complicated. The four screws provide sufficient holding power, eliminating the need for the tabs.

This will work on both the OEM spare wheel retainer as well as the replacement of my own design. Designed to work with a half inch drive, be sure to print this with decent infill and from a good material! ... If this has been helfpul to you, please...

... off the gear capsule. Made in Tinkercad https://www.tinkercad.com/things/1h7e7EdON3R Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Hatchbox PLA Grey Category: Construction Toys

I designed a straightforward retainer to stop a power strip from being yanked out of the wall socket all the time. Since this is my initial project, I expect it can be refined further, but it functions effectively so far. The printing process happens...

I was surprised at the OEM cost to replace my broken cargo net retainer for the trunk cargo net on my 2007 DTS. So I made my own. I made it in two parts for support-free printing. ...The inner post thread is 7mm, but I included the Fusion 360 files so...

The OEM part number for the 3000GT Spyder quarter glass pivot stud retainer is RE8615AXX. Both STL and SLDPT models were successfully printed in ABS plastic. ...It's essential to orient the design with the slicing direction aligned to the finger grip,...