3d print porsche

Screws come with EAF. 3X M6 hex nuts - two for EAF adapter and one for TP-Link adapter If you use a William Optics Dual-Sided 210mm or 245mm dovetail plate, use the following bolts: 2X M6x60 SHCS for riser 2X M6x20 SHCS for EAF adapter 1X M4x16 SHCS...

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

Print Settings ==================== Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm ###Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and...

All parts should be printed first. Then the holes are drilled: the hinges with 4mm and the screw holes with 3.5mm. This gives you optimal support and a high degree of accuracy. The brackets are designed for doors with a 2mm distance from the...

Print these two pieces out then hot glue them to your broom and refrigerator. My broom has its brush cut at an angle, so orient it so that it naturally falls over towards the back of the fridge. I designed this for a .85" diameter broom stock. Let...

Parts are not oriented for printing. The STEP file is included for easy remixing. I am not an electronics expert but I did the best I could with the design, but still make this at your own risk and let me know if you see something that can be...

K40 Paint Rack I recently started painting sla printed miniatures. Soon a lot of 25mm paint flasks crowded my workspace. So I was in need of some paint rack. I searched thingiverse but found none that appeals to me and whose parts will fit in my K40...

It is very important that there are no gaps between the screw and the walls of the tube, so if the screw is rubbed it should be so, it will quickly get used to the walls for this if the printer prints in plus, there are screws in minus. The back...

Note: Someone has mentioned the possibility of additional electromagnetic interference generated by the psu by removing the metal lid, so I may try to print this later in conductive filament. As of now, I have yet to experience any downsides of using...

An extra panel could just be printed and glued to make a longer box for the bottom and top. So adding an extra panel and gluing that in would be a long enough brick. It would add about 4 inches to would make a 10 cubic inch inside kiln which would...

Regarding our parts list, we are utilizing all very common parts and easy to print CAD parts. Our system uses very basic electronics built on a common platform Arduino, but can also utilize any laptop plugged in. Our motors are very common NEMA 17...

for those who download an try it, all i did was use m4 bolts stuck inside the ends of the tubes after going through the arms then zip tie around the threaded section of the bolt to keep it from slipping out, but do whatever works best for you, i...

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

#Printing tips Parts are designed to favour interchangeability and symmetry between ENG1 and ENG2, so they are easier to replace. **STL files are oriented randomly, please adjust side facing the bed so you get the least amount of overhanging...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

Once the bed has been measured, dropping the nozzle to print height will bring the nail back in range of the magnet and retract it to the stowed position. The M5 iron grub screw attracts the magnet back to center and also helps extend and...

Tighten lightly, and you're good to go. Print instructionsCategory: Sport & Outdoors Summary Update 12 Oct 2019: The original design worked pretty well, but wasn't perfect. I redesigned it from scratch in Fusion 360. There are now three...

The main container and the insert are the same for all heroes, so 7 identical main containers and inserts must be printed. The lid is decorated with hero relief. There are 7 heroes in the game and there are 7 different lids dedicated for each one of...

You might want to widen the holes for the screws with a drill (depending on the printing quality you select). 3. Before assembling anything to the case, use a blow torch to warm up the screw brackets and screw in the screws to gently form a thread...

I had just finished printing and attaching the V7 fan duct when I took that pic, so I know the whole thing works. However, the picture shows an earlier rendition of the carriage. I moved the inductive sensor mount to the right a couple millimeters,...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

As for printing requirements, please note that some of the parts in the images do not match their .STL file counterparts due to an error on my part. I uploaded images that demonstrate how to obtain the correct pieces if you encounter any issues. All...

This design is intended to be a relatively affordable, simple and easy to print electronics project. Remix as required to add a secondary sensor, extra valves, etc. I have uploaded the most current Parasolid assembly file so feel free to dive into...

Be sure to print the version appropriate for your application. In order to mount 12mm/14mm wheels to the adapters you first need to install <b>(1) M4x12 or longer socket head screw</b> through the center of the adapter (see pictures for...

All parts are printed, including hinge pins. I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to...

print each part. arm2.stl and c270_lens_adaptor_0.6875inch.stl need support.2. Disassemble the Logitech C270 and remove the PCB. Refer to ‘How to remove the PCB’ for how to remove it. 3. Attach the PCB to the c270_pcb_case.stl. The screws used for...

Again, check several times before you drill. Overview of some assembly steps and setup here: https://youtu.be/QQAKxDcRNgc Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 200 Infill: 15% Filament: Mainly...

Erdhummelkasten&nbsp;DetailsOb Marienkäfer, Schmetterling, Hummel oder Florfliege. All diese Nützlinge finden in diesem Insektenhaus einen willkommenen Brutplatz und Unterschlupf. Diese Werkpackung ist konzipiert, dass für EINE! der oben angeführten...

It doesn't cost you anything extra, but helps me out a lot :) Both links in this post are affiliate links. Print instructionsCategory: Hobby Summary Update: I added a second version of the top part of this case, which has a cut-out for those who...