3d print mining frame

Plus tiny stool.  - Cupboard with microscope top option All the parts are pre-supported for SLA resin printing! This set works together with the Medical Bay set (the table, drawer & cupboard top options are interchangeable - there is also some...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 1 Rafts: No Supports: No Resolution: .3mm layer height Infill: 25%, 2 extra shells Instructions Parts The included file parts.pdf is a list of the parts needed, along with costs and...

Deprecated: Please use newer V2. This is my attempt to design a mount for the Bondtech LGX extruder with the LGX FF for flexibles hotend kit. The extruder is mounted sideways attached to a mounting plate via two M3 side screws into the extruder...

Details and links in the description below. Print instructionsI  used Fusion 360 for this project. Thank you Autodesk for letting me  play with your amazing tool! </p> <p><strong>NOTE</strong> The Fusion 360 file attached as a ".f3d" file but the...

One uses 3mm rods glued in holes to support these, while the deeper one has a printed base and so a larger space for electronics. There's a groove at the rear for an aerial from the receiver, if it has two, so they can be at 90 degrees. The body lid...

I printed these parts using a delta-style printer, employing the following settings: For the Rings & Handle: - Layer height: 0.2mm - Outside perimeters: 2 - Top and bottom solid layers: 3 - Infill density: 20% full Honeycomb For the Clamps: - Layer...

hi,\r\nplease like if you enjoy \r\nthe green wall i made it pretty easy\r\nyou can extend the system with regular 80mm pvc pipe pieces\r\nit is also best to use sprinklers in the module reservoir but a hole will also do fine\r\nfor best results use...

Important Update - 22-08-2016 Please refrain from printing this design version as it has been found to contain incorrect belt paths, not set up perpendicularly. Check out the discussion on RepRap forum at:...

In the security set, you get: - Long & short barricade walls - Corner and straight connectors - Turret connector bases - 3 different defence turrets - Alarm siren tower - Security camera tower - Burn plate with fuel module All the parts are...

It is assembled with a 0.2 mm extra length to make up for round corners when printing the pieces separately. Keep in mind that this model IS NOT TESTED since I do not own such large printers. Uploadet per request. <b>Thanks!</b> Once...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

Post Processing: As I usually do with my prints, I remove the supports, then sand it down, after this I apply two coats of primer, sanding between coats. Once the model is smooth, I start painting the model using acrylic paints and DaVinci feather...

The case is designed to be printed with a layer height of 0.2 or 0.3mm. You can lower the height if you want more details which is recommended for the ARC reactor. Supports are needed on some parts.I used PLA on everything but the electrics carrier....

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

Insert the UBEC into the printed UBEC mount and screw into place in the cover. 5. Insert the mains socket/switch housing that was removed from the stock cover, and screw into place at the rear of the new cover. 6. Insert the original 24v printer...

Endstops The Y-Axis endstop is a single mount for both front and back switches, activated by two tabs mounted under the bed with M3 screws, nuts, and printed M3 T-nut converters. The upper Z-Axis switch is clamped to the Z-Stepper motor RHS...

There is also an experimental EDF holder, not even printed it yet, that would attach to the Body Lid or anything else. The base can be fitted and the two parts glued together. Just an idea but worth putting here. Again saw a Flite test plane with...

There is a bonus version for those who can print multi-material with a Zelda Triforce design. While the two hooks on the sides do a great job of keeping the handheld secure, the hooks on the bottom and top needed slight tweeks. The hook on the bottom...

this is an afterburner direct drive mod for the "tronxy x5sa pro" currently the e3dv6 hotend and the dragon hotend are supported In Y axis you lost 10mm print space these things are needed for the afterburner: Cap screws M3x6 2x M3x8 3x M3x12 2x...

To taper this wing just print the airfoils smaller and smaller to give the taper. So to reduce chord to 50% is easy. When you resize in a slicer it will tell you the length of the chord. So you just need to reduce this by typing the new value into...

Print Settings Printer: Other Rafts: No Supports: No Custom Section How I Dreamed Up This: To make this, you first have to create the base of the ship using a rectangular prism, then use the triangular prism to make the keel of the ship. Next, you...

My plexi has arrived and fits tightly, but it's essential to measure yourself as you build due to print expansion and margins for error in cutting. Measurements are: * Main Panels: 446mm x 524mm * Door Panels: 213mm x 524mm Other objects used in...

The Stem-mount parametric model didn't produce flat sides with larger stem sizes which made it hard to print. I've updated the .f3d file so it forces flat sides. I've included two properly parameterized Fusion360 f3d models so anyone can now create...

The keyboard's design is based off the Preonic layout.&nbsp;Printed on MK3S at 0.2 layer height and brim in Prusa PLA Silver. No supports, make sure to have the bottom correctly set on the build plate.</p><p>What you will need in addition to the list...

... support manned missions indefinitely. This project was created by myself and Dan Pettit (fellow IGG developer). Due to printer maintenance, I haven't been able to complete the printed parts, but it's nearly finished, and I'll post pics very soon.

... As an option, the NEMA17 motor strapping allows to fix a motor with two 3mm diameter screws. Note: The instruction mentions that some parts are designed to be printed without material support, and that the device has been modeled with Fusion 360.

Use in place of magnets and glue both sidesCast a line out with a topper connectedConnect the body, and weight if desiredWait for bite indicationHook fish then pull the bottom off to reduce weight on the line when reeling inReel in, repeat Printed...

You'll need to print two of these, but don't worry about mirroring since this is symmetrical and so is the gap it fits into. You will need to upscale this object by 12.7 times or with an X, Y, Z of 101.6mm x 31.74mm x 10.38mm. With this scaling,...

Insert that STL into your printer, as it takes longer to print than you need to set up the pi&ssd ##2. Just follow [these instructions](https://www.raspberrypi.org/forums/viewtopic.php?t=44177). It doesn't take as long as *paulv* wrote in 2013.... I...