3d print microphone stand

I recently purchased a microphone that came without a stand but had a tripod mount, prompting me to create my own stand for it. Be cautious that this model uses the larger 3/8-16 UNC thread type, not the smaller (more common) 1/4-20 UNC thread found...

A simple cable clip designed specifically for use with XLR microphone stands like the Neewer NW-35 model. Cable diameter: 5.5 to 6 mm Stand rod: 10x10 mm in dimension. Print Settings: Printer used: CTC Replicator model. Raft requirement: Not...

Designed for SM58 type microphones.

The plastic bolt was clipped on the original stand adapter, can be taken off by force.https://fifinemicrophone.com/products/fifine-k683a-type-c-usb-microphone 

I just wanted a stand to hold the holder of my microphone, and then I wanted to be able to adjust the height so here it is. ... The head screw is made specificaly for the holder of my microphone but it should be relatively standard

Condenser Mic Holder Base. ...Ideal for supporting large condenser microphones on flat surfaces. Print Specifications. Raft Settings. Enable Rafts: False. Support Material: Any. ...Infill Density: 10%.

Print two microphone cable clips compatible with a MakerBot printer using ABS filament, as they are reportedly more flexible and robust than store-bought alternatives by the customer.

A clip designed specifically for organizing wires on a microphone stand is available for use. ...The product measures approximately 10 cubic millimeters in volume, or about one cubic centimeter.

Powerful microphone stands are equipped with sturdy clips that securely hold both upper and lower components in place. ...The lower clip features a spacious compartment designed to accommodate the audio cable connecting your tablet, ensuring a stable...

I wanted to have my new Fifine microphone under my monitor so I designed this desktop stand. ... Not optimal because it's not directly in front of the person but it should be fine.

This sleek AT2020 microphone stand perfectly complements my workspace, discreetly tucked away from view behind my monitors. ...Its cleverly designed 30° angle tip ensures stable positioning, eliminating the risk of accidental knocks or spills.

... thread that Mic clips demand, so I decided to share it with the community in case someone else needs one. The custom-built stand measures 130mm from base to mic clip and is more than robust enough to securely hold my heavy Rhode microphone.

I lost the stock stand for my Blue Yeti USB microphone, so I designed this stand with a slot for the oval extrusion on the bottom of the microphone to fit into. There is a slot for the USB cable to fit into, but I did not design a similar slot for...

This interface piece bridges the gap between the mic stand and the microphone suspension - a design seen in Rodé's setup. At one end, it features a 3/8-16 UNF thread that fits standard microphone stands perfectly. ...A M6x15mm bolt is used to tighten...

Secure your GoPro camera to a sturdy stage microphone stand with a 3/8-16 thread. To maximize stability, print the part on its side. ----- If you appreciate my work and want to show some support, consider buying me a cup of coffee! ... <a...

all versions of this stand can be printed without supports, rafts, or even infill. however, I recommend 25% infill and 4 walls to increase the rigidity and weight of the part. for best surface results, use concentric top surface pattern and a...

... to attach securely onto the small, slender segment of the mic stand's structure. ...It expertly adapts itself to work in harmony with tubes of 15mm diameter, a measurement commonly found on some microphone stands as either the upper or boom component.

# Explanation I bought a kinda-cheap ($40) microphone from Amazon Basics that came with a stand that was too tall for me. I wanted it to sit under my monitor but it ended up covering part of it so it had to go off the side, which was bad for...

Hey everyone, I'd like to show off my custom microphone stand that I came up with when I picked up a mic without a boom or stand included. It should work with most standard shock mounts (check out the pics). To get the best results, print it with a...

Recently I obtained a GameCube microphone and the game Odama, but the controller clip wasn't included (and wouldn't fit on my RetroFighters BladeGC anyway).Since I planned on using the mic while streaming the game, I realized it would be a good idea...

Recently I obtained a GameCube microphone and the game Odama, but the controller clip wasn't included (and wouldn't fit on my RetroFighters BladeGC anyway).Since I planned on using the mic while streaming the game, I realized it would be a good idea...

... it to the arm requires an M6 25 mm hex bolt with nut. The legs from the microphone have been removed since they're no longer necessary due to the stand's presence. ...This setup gives my Zoom conferences a retro-style feel that I've been aiming for.

The Samson C01U microphone comes equipped with a simple stand that demands minimal setup. To get started, simply submerge the upper bracket in warm water and carefully bend it inward, allowing the detents to function as intended. ...With this...

Humans use a microphone stand with a parabolic reflector, positioning their voice at the focal point within the curve. By directing the parabola towards your mouth, you can comfortably place the stand anywhere from 1.5 to 3 feet away. ...This eliminates...

This was a custom-designed stand for my Razer Seiren microphone, built to fit the unique adapter that attaches directly under the mic's body. The screws used on this stand match those provided with the Seiren itself, ensuring a seamless integration.

This is the second version for the PS2 SingStar Microphone Stand. (First version: https://www.thingiverse.com/thing:3087036) I've upgraded it because after some use, I noticed some issues that I could solve. First of all, the arm in this second...

This is the part that lets the mic stand clip onto the arm holding the microphone or camera in my case. I designed it to be just like the original that broke, but mine's made of plastic instead of metal. That makes it pretty fragile and not great for...

A microphone stand I made for my elgato wave 3 microphone. I wanted something shorter and out of the way. I used a .4 tip with standard quality on my CR6, but I bet a .6 tip would do fine. I made the inserts to the base a snug fit so it doesn't...

The standard print size is 180x180x210. ...This measurement is suitable for various microphones from the Rode brand, including: NT1, NT1-a, and NT1000 NT2, NT2-a, NT2000, and K2 Rode Broadcaster Rode Procaster Rode NTK

A sleek accessory for microphone stands extends functionality by six inches, featuring a sturdy 5/8-inch threaded attachment on one end and a compatible 5/8-inch socket on the other, designed for effortless mic placement. It also incorporates a...