3d print luffy

values_for_discrete_vars= { "x":[0,-118], "y":[0,-99,"b"] } possible_inputs_combinations=list(product(values_for_discrete_vars['x'], values_for_discrete_vars["y"])) def run_optimizer(input_value): result = minimize(objective,input_value) # Optimizer...

Parts are not oriented for printing. The STEP file is included for easy remixing. I am not an electronics expert but I did the best I could with the design, but still make this at your own risk and let me know if you see something that can be...

The single could be used in pairs at the junction point of the arches if desired or if your printer won't print the larger double base. I have supplied 4 different versions of the single with cable exits coming from different angles to allow for...

You can either twist it in or just force it in in the right spot (Z, I mean).BEFORE all major components BUT the PINDA, attach the printed plate to the TOP TWO bearing blocks.Do the back fan third. The bottom screw is a little hard to access, but it...

For the actual printed parts, this is designed for the tolerances I have experienced with hole shrinkage. It is intended to be relatively tight to the shaft so gently clean out the hole and push onto the shaft. It may take a couple of times to get...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

The alternative file is what is in some of my first renders and does look cool, but they are often annoying to print and glue on the vehicle so adding them is up to you. Size of model when completed 165mm length, 90mm width, 68mm high. ...Instructions...

Then print the 2 models and install them on the printer. For the sensor set it in retract mode and touch the nozzle and the bed. Then place the 2 mm (approx.) allen wrench supplied with the printer between the tip of the sensor and the bed and screw...

When the dice are printed, students will then perform an experiment in which they roll the dice separately a certain amount of times and keep a tally chart of numbers that appear. Students then compare the theoretical and experimental probabilities...

... It was only off .13mm (.0051 inches) at the most, but not really an issue if you have printed the parts already. Here is very short video of this machine working. https://youtu.be/HgV3grxkY44 I also added optional **CantileverStablizer.stl**.

40x55mm.you need 2 pieces of rubber band, wire or tape.you need 1 piece of Periscope tube 01 or standard 32mm PVC tube.(Periscope tube 01 89mm long results in a Periscope in/out of 150mm)But you can also use standard 32mm PVC pipe to get a larger...

The FC mount can be printed using either flexi or solid filament, but flexi gives the FC added vibration damping. The motor dampeners are designed to be flexi as well, but they're not essential for the build. The FC of choice cannot use pinned...

Printing Select the vertebrae that you need and import them into your slicer. You will need to apply supports to the bony parts that stick out the back and to the sides. IMPORTANT: Be sure to label the vertebrae as they come off the printer! ...

42.3mm long and both chamfers.Download the STL and print itYou will need:x1 Blade with screw x1 Screw M3x10mmx1 M3 Hex Nutx1 1.5mm 60º angle toolIf you want to support us, you can also find the full kit...

Buck Converter (to power my 12v cooling fans) Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so...

Print all the parts before assembling anything. 4. Start by assembling all the windows, doors, and trim as shown in image 1. 5. Assemble the motor mounts by gluing the two halves together. Ensure you align the holes before gluing. 6. Attach them...

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

It will then print out a message to the console with the planet's name, its description, and its scale. Please note that this is just an example script, and you may need to modify it to fit your specific needs. Additionally, this script assumes that...

Printing Tips: 30% infill at 50 mm/s If you wish to design your own fraction piece, you’ll need to know the size of a whole. One whole piece is 50mm tall with a diameter of 50mm and an inner diameter of 12.5mm. ...With those measurements, you should be...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

I use resin to print it myself due to the higher precision. If you own a soldering iron you can also solder one of the poles of the motor to the case itself and straight connect it to the rca-connector like I did in the photos attached. (photos to...

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

I've printed a half-dozen of ‘em and they’re smooth as butter. The M10 coupler will screw into the Bowden tap nice and easy by hand.</p><h4><strong>Instructions&nbsp;</strong></h4><p>The pictures should be easy enough to follow but just in case here...

--------------------------------------- The new Spool Winder: You will need: Print the winder parts: WinderHandle - need 1 WInderHub - need 1 WinderLeft - need 2 WinderRight - need 2 SpoolHolderBaseA - need 2 SpoolHolderBaseB - need 2 Hardware...

Other Notes: I printed these on a Super Racer @ 100% infill, 100m/s 210/60deg. I wanted them solid to transfer as much of the vibration as possible through to the pedal. Probably doesn't need to be that solid but they still took less than 1 hour for...

I recommend printing them too. Intentionally the Main Box fits 6 of the Double Mini Card Containers, one big Tarot Container, 6 Standard Card Containers and the two Token Holders. If arranged correctly you'll be able to replace one double Mini...

Screws come with EAF. 3X M6 hex nuts - two for EAF adapter and one for TP-Link adapter If you use a William Optics Dual-Sided 210mm or 245mm dovetail plate, use the following bolts: 2X M6x60 SHCS for riser 2X M6x20 SHCS for EAF adapter 1X M4x16 SHCS...

This is better than putting an oscilloscope probe in your helping hands. Print instructionsRoadrunner Probe Revision A Released 2020-10-04 Copyright (c) 2020 Josh Myer josh@joshisanerd.com Released under a Creative Commons CC-BY-SA license What is...

You’ll need a large printer for the Converter to accommodate the handles but it was necessary to print in one for strength (peace of mind when a £500 drone hangs in the balance). The phone clamp requires an 80mm M6 threaded bolt (I buy threaded...

By default the motion range is 2.5mm, but this can be tuned in the SCAD file. Print instructionsThese mounts should work well in either PLA or ABS with any layer height. Once the SCAD parameters are tuned well for your printer the clips should be...