3d print knitting machine

HotBed = Factory Item I would recommend placing a silicone thermal pad and a sheet of glass on the heat bed for better prints. Power Switch = Standard PC fused and lighted This upgrade allows you to actually turn off the printer with a switch...

The same cable must then go to the component to be coated and be attached there with an alligator clip, for example, and finally be inserted into the ground with an earth hook or plugged into a socket with a printed plug with a metal pin on the...

print a large end and glue it to the screw head. I'm attaching this as a .STEP file... I'd rather you take a look at this F360, Freecad, etc... it works great as is, but I'd love to get some feedback. I'm open for any suggestions on...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out. Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. At...

if your endstop position of your head is in the lower left but the print area starts 20mm to the right and 20mm up than you need to set this: ** **#define X_MIN_POS -20 ** **#define Y_MIN_POS -20** **#define Z_MIN_POS 0** **Enable EEPROM settings**...

Important notes: All parts can be printed without support, except the steam. There are two models, one opens to the right and the other to the left. The discs with the numbers are used for the two designs, and to fix the combination you have to look...

For this team project i worked with Joanna Su (link) Problem Statement: With a partner, you will design a “2D” placard using Solidworks.  You and your partner will have the same design which meets the constraints below, and you will EACH use...

Your slicer should be able to handle both. The other version is also marked as a source so maybe the original creator will implement these changes in the base version (you can tell this is a remix if you know where to look and he/she might be able to...

Print nose with supports everywhere and 20% support density. Also use 20% support density with support brim, support roof, and support towers enabled on the LID. Use four walls and 20% infill or more on the nose, and 40% on the LID. The lid also...

The print time for this project is around 13-15 hours with a layer height of .28. https://youtu.be/-cRUheSAXM4 [Update 2] After finishing my assemblies and using them, I can confirm that the coupler I made is strong enough to handle the cleaning...

Glue is probably optional (to hold the nuts in) but can't hurt. Parts are not oriented for printing. STEP file is included for easy remixing.</p> <p>Updates:<br/> 4-5-2020: Super minor update but may help a bit, thanks to feedback from GreenMotion...

I was constrained by the size of the rotary switch and the USB breakout board otherwise it might have gotten a bit smaller. See it in action: https://youtu.be/PTTVuVUZYM8 I have included the OpenSCAD file which is somewhat parametric. Print...

EDIT 01.07.2020: Added a foot to be printed in TPU, one for each corner. Holes are already drilled into the case's bottom; use M3 screws to secure them. This is a fully self-designed BT-Speaker setup that you can download and edit as you like. A...

... Make sure to use a 7.4v battery. If you use the 6v motor listed above, do not use a 12v battery. Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Resolution: .2

I have a modified version ready for printing, or you can simply cut out the piece that's in the way and make a new one. That's how I did it. V2: But if you want to order a new display and do some modifications, you can also just swap the original...

Required printed parts: 2 each - Thing1 1 each - Thing2 1 each - Thing3 1 each - Thing4 Required purchased items (blue LED used, white would be better): 1 each - 5mm x 20M Double Side Adhesive Thermal Conductive Tape For Heatsink...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

16 crochets sont insérés dans les 16 trous carrés de la roue du haut. Je laisse les fichiers fusion360 si quelqu'un en a besoin, pour les adapter par exemple. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes...

The "Upper parts" contains: -Mosquito/Dirt Blocker (updated to be perforated) -funnel -Pipe attachment (needs to be epoxied/glued into bottom of funnel) -Feet should be printed as needed. need minimum of 4 feet to support weight. The "Funnel" STL...

*** Edit 29JUN21 *** I added : -- A plate V2 : The fan duct outlet are 20 degres tilted instead of 30 degres in first version The holes that allow the tightening of the screws are lightly closed (approx 2 layers) so that the overhang print is...

To print this model, just remember a few things: there's no need for supports in any of the parts, and the printer should be accurate enough to handle shapes like the fan case and fan holder. When you assemble the fan case and fan holder, there will...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

PLA in my opinion is not resistant enough (humidity, temperature etc.) The logo and the wings are colored in orange and silver. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 40% Filament: CPE...

I've split the provided top shell part into pieces that can be printed separately. The now separated flanged sun shields are inserted into the openings from the front side. They're glued together with the case and internal transparent neutral white...

This is the version I have printed and pictured. Will check compatibility with the Gen L board when I get a chance. Renamed files to help clarify. 8/30/2020: Added a new bottom file for the MKS Robin Nano. 6/11/2020: Added the text file instructions...

Potential fixes might include: * a "print-in-place" design for the cap which includes a solid and captive axis pin, * replacing the M2 screw with a very small rivet (strong, but not desirable due to tooling requirements and permanence of...

------------------------------------------------------------------------------------------------------------------------ Old Description...

I also wanted to have all the tips and other accessories next to the soldering iron placed on the control block (easily removable because glued with velcro).I added a blue diode for the presence of 24V, a red diode to display the PWM output activity,...

I have to find efficient part cooling solution, this one does not cool enough with speeds I am printing now. VERRY IMPORTANT! Use correct lenght screws for motor mount. Slightly too long and mount points will be ruined! Parts needed: 2x 445mm X...

(And why on earth is Print Screen so close to the Page Down button, anyway?)Mice and trackballs were obvious options too, but just like the keyboard, they required more precision and dexterity than I could muster on the move. I even tried a couple of...