3d print glock frame

Here's a poorly recorded video of it running on 100mm/s: https://www.youtube.com/watch?v=GovX9jY8XzE ## Change Log 2019-05-01 * Moved the Horns Duct to a separate thing: https://www.thingiverse.com/thing:3600021 2019-04-24 * After some testing I no...

The pegs are quite thin, so it's best to print them with a layer height of 0.08mm. This setting should make the pegs strong enough to hold up to inserting into the bracket but flexible enough to slip into the bracket with little force. I've also...

If you want to support my work, you can contribute with me by donating to this PayPal account. Print SettingsRafts:NoSupports:YesResolution:0.3Notes:If you set the wall width to one filament line (0.4~0.6mm) and the infill overlap to higher...

Printing both pieces or separately. I have also included the .gcode files for Prusa MK3s printers. .2mm layers. Notes: The clip takes some effort to slide onto the meter. It is a bit tight. Just wiggle it a little side to side and continue...

Shelves may be added above or below as necessary.Included:Hinges: print in place w/o support, that also serve as the fixed side of the latch. The latches are secured to the shelves with #6 x 0.75" wood screws. The other side of the hinge has a slot...

RPi3 Model A can be mounted too, but a lot of creativity would be required. Assembly requires some screws. Driver board – 4x M2, M3, or #4 wood screw (example) Mounting brackets – Some M4 or #6 machine screws (example) （更新 2019/3/8) 新しいバージョンを公開しました...

I personally prefer the classic SW-0 to the fancier SW-20, and that's what we've got at the shop as well. I've added provision for screws for mounting - our shop stand is mounted to a plywood base, so this will let me attach it permanently. Print...

It should be a solid friction fit if printed with a semi-tuned printer. To make it more accommodating, there are slits in the grips for the power supply. Cable management has also become significantly easier, with the cable wrapping around the...

Print Settings: - Printer: Sintron Prusa - Rafts: None - Supports: None - Resolution: 0.3 mm - Infill: 40% - Notes: No fan being used. Supports are needed for all sensor brackets. Designing this project involved combining the inspiration from...

1x Brand NEW Warlock Subclass: Dragon Patron 1x Full size A2 printable map of Greypeak 1x Full size A2 printable map of the city of Vanlund 6x original Battle Maps, including an enormous dungeon (for use printed or digitally) 10x Original Statblocks...

#Installation instruction: ##Hardware: Print, sand, use some hot glue to attach the screen to the shell and to glue them together. ##Software: Requirements: none for standalone version www + php server - in my case Lighttpd + PHP on Raspberry Pi 3+...

* **Slides: sacrifice layer for successful prints** The track slides are designed with a 1-layer-thick sacrifice layer covering where the bolt hole transitions from hex-head area to round-shaft area. You can burn that thin layer out with a soldering...

If I had included lips or ledges, the resulting tree would have been too narrow to print smoothly. Take a look at my other trees and their bases if you want to see what I'm talking about - just click on these links:...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. Die...

... convenience. Feel free to modify them however you please and post remixes for the community to benefit from! Print Settings: * Printer: Flash Forge Creator Pro * Rafts: No * Supports: Yes * Resolution: 0.200 microns for most parts * Infill: 40%

While I haven't printed it myself, it should work just fine. *** 9/27/18 *** The main litho no longer needs to be resized (I've renamed it to MainMashup.stl). The crown's orientation has been fixed, and all the parts should fit nicely together now....

My plexi has arrived and fits tightly, but it's essential to measure yourself as you build due to print expansion and margins for error in cutting. Measurements are: * Main Panels: 446mm x 524mm * Door Panels: 213mm x 524mm Other objects used in...

Stick the long M4 bolts into the bed and under-bed with the new springs between the two, then slide on the printed brackets with your tube inside. Slide the thrust bearings onto the bolts, and screw on your knobs. The knob will set the upper thrust...

To get GPIO pins working properly for this print, please follow these steps: Before you begin, please follow the steps in this walkthrough: https://www.klipper3d.org/RPi_microcontroller.html?h=gpio You do not have to follow the link under Remaining...

... have more question contact me for: srheuropeeu@gmail.com The files are for personal use only, non-commercial, not for resale! You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints/builds of the model.

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

Designing and drawing this model required over 1200 hours of work, and printing it took an estimated 2000 hours. The model uses various colors in PLA, including True Red (10 pounds), True Yellow (2 pounds), True White (8 pounds), True Black (4...

Your slicer should be able to handle both. The other version is also marked as a source so maybe the original creator will implement these changes in the base version (you can tell this is a remix if you know where to look and he/she might be able to...

That way, it's easier and faster to print only the part that needs a change. I'm not entirely satisfied with the latest files (some fixes are needed), so they're marked Beta for now. I will set the Tinkercad files to public as well if anyone wants...

Print the required parts (some will need supports), glue the splash guard to the top of the airlift pump as pictured, cut the mesh to size and glue through it with the mesh retainer holding it in place on the holding basket's window (superglue was...

Print that inner panel whatever color you wish and use white LEDs to shine through, or any combination of plastic colors - LED colors, color shifting, or controllable I use two buck converters like intommy does, but with a slight difference. The...

Put it in dedicated place  and then glue both parts together as it it shown in instructions below: ASSEMBLY INSTRUCTIONSPrepare desired Bottom Base (Flat or Hollowed one) and 4 Corner Columns Pour some Superglue (or one you use to bound your printed...

Once they're printed, just glue them onto the faces with your favorite glue - I like SCIGRIP 16 10315 Acrylic Cement. Pacman and the ghosts can be hung either with double-sided tape or with screws using the provided slot. The dots are designed to be...

You'll want to print two of them and ensure they both line up when drilling your holes. The X alignment (side to side) is absolutely critical for the drill guide, while the Y alignment doesn't really matter. Update 3: A new version of the Combined...

I added a backing to the filament run with a very slight channel to help guide the filament through the sensor path and into the outlet fitting without interfering with the actual operation.After testing this setup for a few weeks and many many hours...