3d print funnel

UNC 1/4 20 - http://ali.pub/4kpo3g I use high-speed epoxy to fix the screw and handle AB Glue Epoxy - http://ali.pub/4hvg7o The elastic that is yellow in the picture is a TPU filament - http://ali.pub/4kpplb I printed a knob from PLA filament -...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

Building Instructions: Assembly: Print all parts first. Put an M3 nut into the opening of the parts called SensorPhotoTransistor and SensorLED. Put these two parts into the water meter main part. Slide rods through holes in the main part and the...

This is installed 30mm below the top of the vertical frame, or any distance you prefer The Z axis and bed are then moved so they are around 42-43mm below the X & Y axis Print one of each part, in the orientation you find them, no supports are...

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

This is due to the different number of teeth in the printed gears for each axis. Feed rate changes the speed of the motors. Be careful to not move the azimuth axis too far so the stepper motor wire connected to the motor for the altitude axis...

These are an assortment of Dust Collection Accessories that I've printed. I may be adding more as I need them or possibly upon request for something. I've also added the actual dimensions to all the parts to make it easier for you to make sure these...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

compatibility note: for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like...

Print Settings ==================== Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm ###Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and...

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......

The mounting holes are identical between that and the Creality 4.2.7 silent board, which is what I have installed in the first 'final' print. The stock 4010 fan fits upright screwlessly in a mount that holds it to the side of the case, and a buck...

Although these files have not been extensively tested through printing, they are intended to be resized to match common modelling and miniatures scales. Target scale - Scale STL files to: - Notes 1/3900 - 0.25641026 - FASA miniature scale 1/3788 -...

There is a through-hole for the display and button cable.I also had to print a stand that is screwed onto the load sensor to get a smaller contact area due to the slight angle of the adapter.Included is a schematic on how everything is connected as...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

The LED-tube itself is printed from transparent plastic. Feel free to install a lipo and a step-up-converter or whatever you want ... There are three versions of the body, for - arnuino nano - node-esp8266 development boards - 49 x 26 mm -...

...There is a preview .stl--nothing to print yet! Updated with v2 parts 09/21/2017: Added longer V2 parts that use two screws for better clamp support, similar to a woodworkers clamp. If you are shooting for light and cheap stick with the V1 clamps.

Note: This will decrease your print height slightly! The CR-10S Pro struggles even more than the CR-10 series when it comes to Z motors going out of sync on power off. This is due to the same design as the one used by hoegee, but it works perfectly...

As for printing requirements, please note that some of the parts in the images do not match their .STL file counterparts due to an error on my part. I uploaded images that demonstrate how to obtain the correct pieces if you encounter any issues. All...

I printed and tested it with four 10 W blue LEDs (450 nm wavelength), but other types and wavelengths can also be used. Using the 10 W LEDs shown here, an 80 mm fan must be mounted to avoid heating the reaction vials above 30 degrees C. If lower...

... Uno. You may also write your own software. I'll also consider requests for a free copy. Send me your request. Print Settings Printer: HyperCube Rafts: No Supports: No Resolution: 0.1mm Infill: 80 Filament: HatchBox PLA Grey Category: Puzzles

This design fits on a Prusa i3 MK3 bed.Note: Please only attempt this if you already have some experience with soldering, wiring and electronics in general.Note: Some ATX PSU's may be too deep for this design so if your PSU is over 135mm deep it may...

All parts are printed, including hinge pins. I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to...

There are two methods you can use, either print up a new modified WhiskerScar with the rib cut out for a 19 mm OD and 16mm ID 1.7 mm thickness o ring (or some close equivalent) or you can use electrical or masking tape on an existing Whisker scar...

... after days, or use a step-by-step motor or a properly controlled servo motor. I took advantage of the suggestion in the comments to widen the dial, so you can read the time well between 9 and 12, the result seems very good to me. Happy printing!

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

These keep everything in place as it should be. If you have any questions then just write to me or comment. And now have fun printing and tinkering. If you like the design, Johannes and I would be very happy to receive a like or a make. Deutsch Ein...