3d print fractal

https://kc9on.com/product/fox-hunt-offset-attenuator/ ###What is what### To use this case, you'll need to print the cover and one of the cases depending on your choice of connector. FoxhuntV5C.stl has no antenna outlet for you to modify it to your...

To print this model, just remember a few things: there's no need for supports in any of the parts, and the printer should be accurate enough to handle shapes like the fan case and fan holder. When you assemble the fan case and fan holder, there will...

... structure (https://www.thingiverse.com/thing:4695870). So I also redesigned the 140mm spindle. It now has a hole at the top where you can put a (colored) steel ball. Also, the bottom edge is rounded to make printing the bottom a little easier.

I have included two versions of the mount, one is with the rail centered on the overall enclosure and the other is with the rail centered on the top part of the enclosure resulting in a slight (5mm) offset from center. I also went ahead and added in...

Shake it again and it's a one minute timer! A demo and step-by-step building instructions is available here: https://youtu.be/lHQFzX9xagM The brads system can be used for any other project without having to sacrifice a Micro:bit board. This project...

I wanted to add lighting to my Kossel so I could monitor overnight prints without leaving lights on all night. The Neopixel range of addressable strips and rings seemed perfect, needing just a single data line for RGB control and a 5-volt supply. At...

I borrowed the mount from MMendel and redesigned the blower to give more print cooling and hold an induction sensor. Also, if you change the hotend, you will need to run PID tuning otherwise the hotend won't get to temperature. And the induction...

I have included the STL files that I used for the demo parts - all were printed on Lulzbot Mini with eSun ABS. This printer has a 0.5mm nozzle (if you use these demo STLs with a smaller nozzle, the fit might be loose). The file names are ridiculously...

Comes in 32mm and 75mm Scale - PreSupported option available (Actual printed size is 65mm and 150mm respectively).   An elite fighting duo that are legendary amongst the front line and special operatives of The Golden Griffins. Just the sight of...

POST-PRINTING There's room to mount a Micro-USB breakout board (see pictures) if you'd like to supply power on the side rather than out the back. These boards can be found here: https://www.amazon.com/gp/product/B0183KF7TM The BoB is mounted to the...

BEC set to 3.66V RMS --> VCC Hall sensor board pin 24 Jetson (physical pin == number printed on pcb) --> D0 Hall sensor board GND to GND This configuration is listed on Slack from @Doug and @Tawn (https://donkeycar.slack.com). Thanks to them! I use...

I found in using my original printed design that the holes didn't allow for the kind of seasoning dispersal that I prefer (lots of it!), so I increased the hole diameter from 2mm for each hole to 2.75mm. This should allow for more or larger grains to...

I strongly recommend printing Mpooh's fuse holder and wiring in an automotive fuse in series with the battery. The battery probably has protection circuitry, but who knows how much power this battery can supply before protection shuts it down. I use...

Once you've printed out this part, and optionally Piercets external tensioning parts, remove the current idler and take the 608ZZ bearings out. Add the additional 608ZZ bearing, put a washer between each bearing and on the top and the bottom of the...

... is important! Save with M500. Next, home the printer with G28 and run a bi-linear level with G29 then save the data with M500 and enjoy! Put the command G29 after the home command in your start G-code to level before each print. ... Good luck!

I printed it in a black PLA to help it blend in better with the Xbox. Edit - Feb 1st '21 - I realized that the smaller file's hanger's were off centered... so I have adjusted that and re-uploaded the stl. I have also included 2 more versions of...

... is how we made it, it's a personal project, so it's ugly in places. I'm just putting this up here in case anyone wants to do this, or do this differently, or use it for something else. Or just print an overcomplicated Bender head, idk. ... Peace.

Please note that if the magnetic tension is too high - for example, if the magnets are too close together - this can soon lead to the printed parts bending. There are two tops to choose from. Here's a video: https://youtu.be/lwLGZ7oSHqY As magnets...

- https://amzn.to/3bAgYBv Uses M3x3mm knurled brass heat-set inserts found here - https://amzn.to/2LQwDld Uses 1 M3x6mm screw found in this kit - https://amzn.to/39q2otO *Note: This post contains Amazon Affiliate links that support The...

Print SettingsPrinter: Velleman K8200Rafts: NoSupports: NoResolution: 0.25Infill: 30%Notes: You'll have to put in 1mm support columns on the base lip where the cups are pulled out. If you let Slic3r handle it there will be a lot of wasted plastic. ...I...

The switches are activated by two tabs mounted under the bed with M3 screws, nuts and printed M3 T-nut converters (T-Nut-M3.stl). The upper Z-Axis switch is clamped to the Z-Stepper motor RHS mounting posts, while lower mounts simply clip on. Ensure...

... holes for the magnets in the block. The Display Base was too large to print as a single part on my printer, so I split it into 'a' and 'b' parts. ...The two halves of the Display Base can be connected using two M3x12 screws, washers, and nuts.

... and have removed the limit switch. If you want to lift the whole machine up so there is better airflow under the case, I advise printing these feet in TPU: https://www.thingiverse.com/thing:3020865 STEP file included for your own alterations.

... points. This needs supports for building (you might try flipping it upside-down to check if you need less material - this depends on your printer). Also added full- and half-height main body extensions (these can be printed without support).

The keyboard's design is based off the Preonic layout.&nbsp;Printed on MK3S at 0.2 layer height and brim in Prusa PLA Silver. No supports, make sure to have the bottom correctly set on the build plate.</p><p>What you will need in addition to the list...

:) My fav PLA on Amazon Italy: Tianse PLA Sunlu PLA+ GEETECH PLA My fav Resin on Amazon Italy: Elegoo ABS Anycubic eSUN Print Settings Printer: Alfawise U30 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Tianse PLA White Category:...

The stock arms were strengthened (now printed separately). Designed support was removed from the trigger well and mid section. The magwell fit and detent were adjusted. More space was made in the end cap for hose. The bottom front picatinny rail was...

Die Schleuder darf nicht zu leicht und nicht zu schwer auslösen.Die Spitze der Schlinge ist zudem notwendig um die Kugel sicher aufzunehmen.Print SettingsPrinter Brand:CrealityPrinter:CR-10SResolution:0,2Filament: Crality...

... the key « f » for fillets.</p><ul><li>Draw a sketch an the top circle under the helix with a little rectangle who will « join » the eagle wings. By doing that, you will have a better print by having less retraction.&nbsp;&nbsp;Category: Automotive

Check out more printing accessories from Department_Nine! ##Similar Designs## Found these after the fact (always hated homework): https://www.thingiverse.com/thing:4727323 https://www.thingiverse.com/thing:2994501...