3d print foregrip

smaller vertical foregrip, uses standard magpul mounting screws. havent brought it out shooting yet but feels good and solid. feedback on it would be great. will update if any changes needed. ... Follow me on odysee for more gun stuff and remixes

The foregrip is 5.5 inches long, 2.25 inches tall and .850 inches wide at the grip. Fits perfect on a picatinny rail using three or fewer screws. ... Fasteners used: 10-32 X 1.25 LONG BHSCS 18-8 SS BLACK OXIDEhttps://www.mcmaster.com/97763A233/ 10-32...

The foregrip is 5.5 inches long, 2.9 inches tall and .950 inches wide. Fits perfect on a picatinny rail using three of fewer screws. ... Fasteners used: 10-32 X 1.25 LONG BHSCS 18-8 SS BLACK OXIDEhttps://www.mcmaster.com/97763A233/ 10-32 NYLOCK...

The foregrip is 5.5 inches long, 2.9 inches tall and .950 inches wide. Fits perfect on a picatinny rail using three of fewer screws. ... Fasteners used: 10-32 X 1.25 LONG BHSCS 18-8 SS BLACK OXIDEhttps://www.mcmaster.com/97763A233/ 10-32 NYLOCK...

Angled foregrip modeled after a popular mainstream model. Actual M-Lok that uses basic M-Lok hardware. -These files are for PERSONAL USE ONLY. They are not to be reproduced and sold. Intellectual property belongs solely to DFDesign. ... -I am not...

This is a custom foregrip I've engineered, versatile enough to be fitted onto Nerf blasters as well as genuine Picatinny rails - although it's strongly recommended not to do the latter. ...Proceed with caution and take full responsibility for any...

... and Regulator models. ...For a precise fit, carefully heat the rail connector with a lighter for a few seconds before sliding it onto the gun. An original foregrip designed for picatinny rail is available at: https://www.thingiverse.com/thing:2436596

Skeleton ForeGrip, an ergonomic grip design engineered to reduce fatigue and discomfort during extended use of firearms. This innovative grip features a textured surface that provides a secure hold on the firearm, even when wet or covered in gloves.

I remixed this foregrip for Picatinny rails as the original design wasn't aesthetically pleasing to me. The holes for the Picatinny rail securing bolts didn't line up properly. This fits and works with a standard Picatinny rail, and I trimmed some...

This allows you to mount and stack additional attachments like flashlights, lasers, more foregrips, etc.... The picatinny insert slides into the bottom of the grip. New side panels replace the old ones and hold a bolt (M5x25mm) and a hex nut to...

The foregrip's design was influenced by the HERA C.Q.R grip, which I wanted to replicate but found too long for my APS UAR's rail. If you have suggestions, post them in the comments below. High-density infill/cubic subdivision pattern ensures...

Short foregrip can only be attached to Stryfe after making precise cuts to the shell and orange component that includes the muzzle and extends under flywheel cage. ... UPDATE January 22, 2020: Revised buttstock file now features a more robust sling...

Vertical Foregrip for keymod style rails. Nice solid lockup to rail. Four versions, knurled, smooth, spiral, and ridged. Modeled using DesignSpark Mechanical. I included an M-LOK version that removes the studs on the bottom that were for keymod...

Since i couldn't find a flat foregrip that i liked i remixed my own from Ernpao's template: https://www.thingiverse.com/thing:3288887 for the model, i designed it for the Worker Swordfish so the rail goes all the way back, i tried to make one for the...

This is a foregrip designed for the quad rail I developed for the Shutty AP9. You can find it here: https://www.thingiverse.com/thing:3081573. It will work on any firearm with a rail! The bolt size is 1/4-20, and I used one from this kit from Harbor...

I wanted to use the excellent Pyrangle foregrip for my Lynx but the standard version was a little loose so I remixed it to grip with no wobble. Now my weedy arms are able to prime my Lynx more easily. Also tweaked some of the holes to fit m3...

This is a step file for the Thompson 1928A foregrip created from WWII arsenal drawings. ... Since this was a follow on of the 1921 Thompson version (that is associated with gangsters of the the 1920's and 30's), and was for military use, this military...

I wanted to use the excellent Pyrangle foregrip (by Captain Slug) for my Lynx but the standard version was a little loose so I remixed it to grip with no wobble.Now my weedy arms are able to prime my Lynx more easily.Also tweaked some of the holes to...

I spent 24 months neglecting my initial design, only to face a grueling weekend battle with my kids before finally deciding it was time to revamp my original Stryfe foregrip. This is the MK2, which brings significant improvements to comfort and hand...

I wanted to use the excellent Pyrangle foregrip for my Lynx but the standard version was a little loose so I remixed it to grip with no wobble. Now my weedy arms are able to prime my Lynx more easily. Also tweaked some of the holes to fit m3 metric...

The SlightlyOdd Foregrip brings forth a solidly crafted, precision-crafted piece of equipment that's designed to provide you with complete control over your blaster. With two secure points of attachment to the Apollo, this product isn't going...

AIRSOFT GRIP Foregrip for keymod rail, 2mm spacing indented into the rifle side to fit keymod nuts perfectly. Keymod nuts absolutely required. *UPDATE* - May 2nd, 2018 It's come to our attention that this grip doesn't follow the keymod spec exactly....

I designed this smaller foregrip a while ago for a pistol I was working on.It is nearly vertical, at 83°.Use a 6-32 x 1.25" bolt to mount the Picatinny.The Mlok uses 2x 4mm x 20mm screws with mlok t-nuts. Update 10/25/2022:Added a Picatinny_V2 that...

This is a Vertical Angled foregrip styled after the MLOK BCM Mod 3. There are a few models so far including one made specifically for the FCG-9 and one for a standard flat handguard. The FGC model has the same angle as the FGC-9's magwell and...

A funky grip I found and converted for picatinny rails and 3D printing. ... Uses 2x M3 screws and nuts.

A funky grip I found and converted for 3D printing. It's actually quite comfortable. ... Uses 2x M3 screws and nuts.

Usually, you don't want this, but 3D Printing requires the balls to stick. Thankfully, the original was graciously uploaded with a CC License so I can share my improvement with the world. Happy printing. ... Go to the original upload for print...

The original design by wolfie1981 had some significant issues on the bottom that made printing challenging due to the balls not sticking properly to the bed, a critical requirement in 3D Printing. Fortunately, the creator released the design under...

A grip based on the Midevil Industries 360 that I and converted for 3D printing. Doesn't fold like the real one, but it might be possible to do if there is some demand for it. ... Uses 2x M3 screws and nuts.

... video at https://youtu.be/vvL08DRc2x0! ... Before printing, I recommend tweaking the design a bit since assembling this model straight from the Fusion360 files can be quite challenging and may result in scuffs and minor damage to your 3D printer.