3d print first layer test

User: I am currently calibrating my MK3 bed using a 240 x 210 square for the first layer, with a 10mm edge buffer for the skirt. This is a straightforward test to verify that my bed is level and my extrusion rates are accurate. ...My default S3D profile...

Check your first layer thickness over the entire bed and check your printing limits. A parameterized and very simple bed level test print. A circle in the middle followed by square rounds to the very edge. From OpenSCAD, set values for very limits...

I designed this so that it would be easier to calibrate my z level. ...When you print this, make sure to turn on bed supports, and you only print the first layer.

Cheers This is a Live z-height test to help get an accurate first-layer height tuned in.The 02mm model steps up from 0.20 mm in 0.20 mm increments up to 1 mm in height.The 04mm model steps up from 0.40 mm in 0.40 mm increments up to 2 mm in...

The Z Height Test allows users to precisely measure Z height at multiple locations across the build plate, eliminating the need for extensive initial layer printing. ...Available in a range of sizes, this tool enables testing on specific areas of the...

Bed calibration check / Initial print layer inspection

This test print will help you to reveal that issue and speed up trouble-shooting. Triangle: Cornes with an angle below 90° are sometimes hard to print at the tip of the corner.While a rectangular shape won't show this issue (cause all cornes are...

A 25mm square single layer test print for checking your 1st layer calibration. For minimum clean up there is no brim, and a small handle to pull the print off the bed without removing the sheet. g-code for both PLA and PETG Two versions of g-code are...

I needed a simple model to check my first layer as I was having inconsistencies so I whipped up this quick 0.2mm thick 220mm x 220mm square to fix my first layer and figured others might have a use for it

I needed a basic test for CR10-S5, and since it wasn't available, I created my own version.

I designed a collapsible fan to check the performance of the initial sheet on the heatbed without wasting an entire layer of PLA.

5 squares of 0.2mm shall be printed, whereafter you can judged whether the bed needs adjustment.

Just a simple rectangle of 0.2 mm to test your z-offset alignment (via bl-touch or any ABL) / bed-leveling. ... Just print it with your first layer setting at 0.2 mm. ... Give it a try and tell me what to improve :)

... just want to see the bed is level stop it before it starts to do the infill. Print Settings Printer: Ender 3 Rafts: NoSupports: No Resolution: anyInfill: any Notes: change the no of wall lines to increase the test time. Category: 3D Printing Tests

Also if you just want to see the bed is level stop it before it starts to do the infill. Print Settings Printer: Ender 3 Rafts: NoSupports: No Resolution: anyInfill: any Notes: change the no of wall lines to increase the test time. Category: 3D...

Print instructionsDefault - 0.24 mm layer height.If you want to print a different height you must change the height of the model in your slicer using the scaling option.

I created this design to thoroughly test my Ender 3 printer as I had been noticing some peculiar marks on my prints lately. The shape was carefully designed to be printed in a single line, making it an ideal visual guide for checking if your print...

I designed this to test my Ender 3 printer as I was seeing some strange marks in the prints. The shape was made to print in a single line and you can use it as a visual guide to see if your print bed is level. It also proved very good at showing me...

Printing with PLA - testing first layer on box shaped object with different infills.

First layer 100x100 mm square with 0.2 mm height 60x60 mm square https://www.prusaprinters.org/prints/9838-first-layer-test-60x60-mm-square

After the bed calibration with sheet of paper I recommend you print a first layer calibration test for better ressults in your 3D prints.Printer Ender 3V2Material: PLA

With this test print, the first four layers become visible on the print bed. So that they can be judged on their quality. Allowing the printer to be better adjusted for over extruding and flow rate The design is available in four variants:...

Simple First Layer Test for Creality CR-10 Smart.

First layer 100x100 mm square with 0.2 mm height 60x60 mm square https://www.prusaprinters.org/prints/9838-first-layer-test-60x60-mm-square

One layer high (0.2mm) loop pattern covering the entire Prusa XL print bed.“Prusa XL First Layer Test 2.7mm r1” - 2.7mm wide loop.  Print time ~8 min with 0.4mm nozzle.“Prusa XL First Layer Test 5.0mm r1” - 5.0mm wide loop. ... Print time ~14 min with...

Line width test print : 0.8 mm Height : 1 mm Area test print : maximum circa 125mm x 220 mm Nozzle standard diameter: 0.4 mm As always, the width of the line should be the same everywhere after the first complete layer. The area in the middle should...

Quick 2 minute print to check first layer/adhesion.

💡 Test your printer's retraction settings and first-layer accuracy with this quick and easy print.The design features circles with 20, 15, 10, and 5 mm diameters, along with central text, to give you a clear indication of your printer's performance....

This model is a test for the leveling of the first layer of the CR-10 Smart printer.

A first layer test for small printers with built dimensions of 10 x 10 cm. ...The squares in the corners should be 10mm wide.