3d print files free

... with this new hose adapter. It is available at the link below: https://www.thingiverse.com/thing:5011414 Print Settings Printer: Snapmaker 2 Rafts: NoSupports: No Infill: 25% to 30% should be fine Filament: n/a PLA Black Category: Machine Tools

Before you start, if you are planning on printing it first and installing it after, make sure you have installed the mount bracket for the stepper motor/extruder. The mount bracket is made to use the mount screws for the two upper rollers. If you...

Designing and drawing this model required over 1200 hours of work, and printing it took an estimated 2000 hours. The model uses various colors in PLA, including True Red (10 pounds), True Yellow (2 pounds), True White (8 pounds), True Black (4...

Trapezoidal threaded nut:Outer diameter: 8 mmPitch: 8 mm (height that the spindle nut travels per revolution)Gears: 4Suitable for Anycubic i3 Mega S (I installed it myself)If you are unsure which pitch your spindle has:move Z-axis to zero...

Print two each of profile holder and spool holder, plus 8 spacers. You will also need 4x 608 bearings and minimum 4x hex nuts and bolts (3x20 will do, but they can also be longer if that's what you have). To secure the holder to the profile...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...

Not only was it my first real model using FreeCAD - which I'm still learning - but it's also my very first attempt at designing printed screw threads. True to form, I didn't start with something simple where you just look up standard threads on a...

(At least in my setup, if the original z-axis endstop was used, you could wire this in parallel as a backup, possibly.) The part is best printed in ABS, PLA will warp over time. Instructions Use...

It's essential that the fabric has a medium-sized print, or the fabric pattern may not match the image of the doll. Tilda dolls are usually carried out in a compact size, so it's best that the fabric is not too large. Dolls Tilda can be sewn two...

small boxes used for storage - I had some space left, so I decided to go with 2 small boxes, which can also serve as a save box - 2 additional magnetic deck holders - for exploration cards, if you throw out one of small boxes you can also save cards...

How to make You can print all parts without support. Place on the build table as supplied. Circuitry is exactly as same as former thing named "Minimal Mechanical Digital Clock with Network Time Acquisition", https://www.thingiverse.com/thing:4931539...

If you're adding them then I'd recommend printing a few extra as I found the mount pins to be a bit fragile - they're only there to guide you when attaching them. Just a dab of superglue will hold the stack mounts in place. Exactly like the...

Of course, it requires a fairly high-resolution printer, 0.1mm or finer, to print these pieces successfully. With a gear train in place, I can now make a more robust small Pan & Tilt that will rotate up to 360 degrees or more. Required Hardware: ...

Thin "windows" are designed into the forward and bottom surfaces of the backpack, which can be cut away after printing to increase much-needed airflow. PRO-TIP: The DTX03 ships in standard-definition mode, but it's capable of recording nicer video...

------------------------------------------------------------------------------------------------------------------------ Old Description...

Required printed parts: 2 each - Thing1 1 each - Thing2 1 each - Thing3 1 each - Thing4 Required purchased items (blue LED used, white would be better): 1 each - 5mm x 20M Double Side Adhesive Thermal Conductive Tape For Heatsink...

- Some nice, yellow PLA (I couldn't find an exact color match, but I got close!) - Revel Contacta glue - A hot glue gun - Some clamps - A soldering iron (with a small tip) & solder - A small, flat-head screwdriver - [Male & female USB C...

I have printed the lid in white PLA with slight indents for added light to come through at the right places. (it allows me to see the LEDs change so that I know it is working and not hung.) The lid is a (tight) push fit that stays in place well and...

A single support (base + 2 side panels) and a nut can be printed for each spool and the spool would only be changed by releasing the wing nuts so the spool screw would not have to be removed. It'll need: -2 bearings 628 / 6-2Z (13x6x5)mm -100mm...

- Different top options for the single width versions: cooling system, computer and surgical implements.  All the parts are pre-supported for SLA resin printing! This set works together with the Science Lab set (the table, drawer & cupboard top...

A 0.3 mm nozzle would be recommended for the rotor blade, I printed with 0.4 mm. On the Nabe, drill out the holes for the screws with 2.5 mm and cut an M3 thread. Glue the Labyrinth ring to the Nabe at the rear with CA. Put the ball bearing in the...

Now you can print everything required for installing landing gear on your Mini Talon easily. https://youtu.be/qJZGLSQbhl0 Parts Needed: - Landing gear kit from Banggood or any wire spring landing gear using M2 wire. - Used for front nose gear:...

You may also request this model printed and assembled with velcro at https://jkl-adapters.com/   Description To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series of penhold...

The launcher handle and rack parts should be printed in PLA (it's stiffer than other filaments) and with at least 3 perimeters and at least 20% infill. None of the parts need supports.LaunchingFirst, roll the wing onto the rack of the U-shaped...

There is a new version of this carriage at https://www.thingiverse.com/thing:3615464 AND an even newer one at https://www.thingiverse.com/thing:3688067 I highly recommend the newest version for better rigidity and simpler printing and assembly! This...

My old wooden LED bases are simple and elegant, but now I've created one that can be printed with ease. The distance between the LEDs is adjustable, controlled by turning the outer ring of the base. This allows for a customizable lighting experience...

The lip from the housing is 7.8mm wide and 1.5mm high. Use double sided tape to attach it.   Thanks for the f3d goes to Core3D.tech from GrabCAD https://grabcad.com/core3d.tech-1 for his KW11-3Z modell...

I'm currently printing 3 perimeters, 6 end layers and cubic infil which has the advantage of forming lots of sealed pockets. To get the cubic infill strong enough I've gone to 30% infill, partly based on one of the Gong designer's youtubes where he...

I print at: X-9.4%, Y-9.4%, and Z-10% to provide a snug fit while keeping the height. Then I attempted to put super glue on the bottom to glue it to the bottom of the keycap. It worked but the key cap choc stem wasn't long enough to push down the key...

http://www.thingiverse.com/apps/customizer/run?thing_id=56795 KeyCut Customization Guide Select Options: KeyCut Code: 66666 Straight Length: [27,22,0] Top Slot Angle: [30,30,0] KeyTip Bot Angle: [225,225,0] Style of Key: 1 Cylinder Layer Count:...