3d print filament roller

A small, simple roller filament guide to help direct your filament straight into the filament runout detector. No need to for any extra screws or fasteners as all the pieces are pressure fit, or use the existing hardware on the printer. The mount...

** Made some final adjustments it's good-to-go) *PULLEY V10 *ROLLER PINE V10 I went back and forth with my filament holders so I figured I would at least make a Filament Guide that I wouldn't have to move. Anyway it's a work in progress but I have...

I remixed the filament roller guide, by antibimmer, to mount directly to the two M3 screw holes in front of the extruder for the Voxelab Aquila. The bottom of the mount has M3 nut recesses if you want to put the nuts on the bottom, however, the...

They snap into place perfectly, providing resistance but still adjusting to width.\nTwo of these and four 608 skateboard bearings get you a completely adjustable filament roller that sits on top of your favorite aluminum-extrusion-frame...

I was drawn to this design (http://www.thingiverse.com/thing:2016985/) specifically for the Anet A8, but didn't want to overload the frame with extra weight, which could potentially damage print quality. I also considered this alternative...

I modified the spools (123-3D) to fit my needs since they measure 73mm in diameter. To accommodate this, I had to alter the width of the base plate accordingly. ...The roller for 608Z bearings remains unchanged from its original design.

People often experience frustration when their spool of filament keeps slipping off the roller, but one ingenious solution has made this problem a thing of the past. I designed a cap that perfectly fits over the end of the spool, effectively...

... roller's smooth shape made it too easy for reels to ride up the sides and fall off. ...I've designed this with a 60-degree slope that will still print well and a sharp transition to lessen the possibility of reels riding up.I hope you find it useful.

Modified for the Voxelab Aquila. ... It required an 8.5 mm additional offset to align with the extruder, and I narrowed the slot by 2.3 mm. It also needed more clearance on the bottom of the slot for the roller hardware. ... Printing: Nothing special.

Manufactured using 3D printing technology, this miniature replica of the iconic structure boasts a sleek, gray finish that has been expertly enhanced by a dash of metallic sheen courtesy of a precision paint marker. ...However, achieving a seamless...

There is a endcap.stl file for the endcap which should be printed in flex filament Parts needed: (6) M3 x 5-8mm bolts (6) embedment nuts M3 (3-7mm length, 4.6 mm dia) (1) drybox (2) 608 bearings 8x22x7mm (1) x length of 1/2" PVC pipe (can be...

ORIGINAL DESCRIPTION I got the idea from adarkstudio to use the factory Ender 3 filament spool holder as a base and attach bearings to it to reduce friction on the filament roll. One part has a lip, one does not - I'm still figuring out if the lip...

Some must be printed multiple times (the pin is needed 3 times, the roller is needed twice and needs to be glued together with a pin connecting the two). You also need an M6 sunk head screw, and M6 nut and two roller bearings type 608 (best to use...

Some must be printed multiple times (the pin is needed 3 times, the roller is needed twice and needs to be glued together with a pin connecting the two). You also need an M6 sunk head screw, and M6 nut and two roller bearings type 608 (best to use...

It works really nicely, I printed a separate washer that sits on top of the roller before it is fitted through and fastened with the nut. I did this to make it easier to print without supports. ...You will need to print all parts once, except for the...

great connector want to add a roller to reduce a little bit more fiction

I created a basic component to immobilize the filament while it's rotating on the extruder during extensive printing sessions.

Simple filament guide for acrylic Prusa i3. ... Used a short piece of PLA filament as the axis. Print Settings: Printer: Prusa i3 Rafts: No Supports: No Resolution: 0.2 Infill: Honeycomb, 25%

Print this as it will help get your new printers filament going in where it should and keep it there. ... Requires 1 608 Bearing M4x16 screw and NUT

... There are two types of roller with a side for centering (roller.stl) and without (roller_2.stl). In that roller with a side bearing, it climbs very tight, it must be pressed with a vise until it takes its position. ... https://a360.co/2OtaVRH -----

... solution to store my filament within the confines of an IKEA Lack box directly above my printer. ...This ingenious setup is capable of securely holding up to twenty 1-kilogram rolls of filament, providing ample storage space for my printing needs.

Please leave me a comment and i'd be happy to assist :) Modified the original Ender 3 Filament Roller Guide I noticed there were minimal remixes for the ender 3 pro which seems to have a different design. So decided to modify this one to work with my...

... One with and one without a required 608 skate bearing. You will need to print only one -- either with or without a 608 bearing I prefer the one with the press fit bearing. ... You MAY need to print the 608BearingSleeve at 101% if it is too snug.

low friction filament spool holder to replace the stock piece for any filament with a 30mm (40mm to fit over the shoulder) center hole.uses 608 skateboard bearings. You will also need an m8x1.25 threaded rod, 150mm long, and a couple of m8x1.25...

Modified the brackets for a filament guide as my bearing holders and spacers and modified the bearing wheels. Print 8 spacers, 4 wheels, and the main bracket. I then used channel locks to press in the bearings into the wheels and oiled the bearings....

... outer diameter of 17 millimeters and an inner diameter of six millimeters. Four M6 screws, measuring thirty millimeters in length, are also required. Additionally, four printed wheels and four printed feet will be necessary for a stable foundation.

As the extruder pulls hard on the filament, every bit of friction removed results in an even smoother print. No additional hardware is required beyond the 625ZZ bearings. The pins (three) may need to be scaled up or down by one to two percent...

... ... This requires no tools, I printed it out of PLA+ but regular PLA would work, I did 3 walls, 15% infill. Print it with the shaft pointing up, and with support for the two 'nubs' The nubs will go in the holes at the top, they just press in. ...

stabilisation et amélioration de la base du guide filament CRX

i have not printed this bracket file but i only thinned the mounting area down a bit from the one i did print which is pictured. the holes in the bracket are 5mm. i used the extra m5x25mm(i think) screw to hold the bearing in place. it should be...