3d print fan duct

Here's a Simple Fan Duct I Designed Using SketchUp 0 I'm super stoked about this simple fan duct design I made in SketchUp. I drew it specifically for fans that are 60 millimeters wide. I created the design using SketchUp, but I haven't printed it...

You can easily upgrade your bridge fan by adding this versatile duct, which allows you to channel air directly onto the tip of your print head without installing a new fan altogether. Since tolerances are extremely precise, be certain that the duct...

... it can also be used on other printers. ... Print Settings Supports: No Resolution: The resolution is 0.3mm. Infill: It comes with an infill of 100%. Notes: Print the fan duct with two shells and 100% infill. ...I suggest using PLA for this project.

This fan duct is specifically designed for use with Lume 3D printers. It perfectly fits the SUNON MF50151V1-B00U-A99 blower model. I'm writing this in English, even though I suspect that this printer's popularity may be limited to Poland. ... A...

Attach a fan duct to your 3D touch's fan for improved PLA prints by directing airflow towards the extruder tip; this can be especially useful when printing small, high-res parts with large overhangs. After testing, I found that increased airflow...

Here is the rewritten text: Design Description I designed a straightforward fan duct in SketchUp specifically for 60mm fans. Guidelines The design was created using SketchUp, but I haven't had the chance to test it yet. At 13 years old, I don't have...

This is very basic fan duct created for easy printing. ...It can be good starting point for customized fan duct

I'm planning to swap out the mainboard fan in my CTC-3D printer because its loud noise has become unbearable lately. Upon closer inspection, I noticed that the fixating screws were a bit loose, so I decided to design this component, which seamlessly...

This sleek adapter seamlessly integrates with your existing bridge fan, redirecting airflow directly to the precision tip of the print head. ...Critical tolerances demand precise alignment, ensuring the adapter doesn't droop below the print head's...

The original modification to the air duct has significantly improved cooling efficiency at the nozzle, but unfortunately, it now hinders airflow from reaching the heater block.

Here is a print fan duct for the Original Prusa Mini. Fits any 5015 radial fan. ...For installation, use an m3 bolt and 3mm nylon nut.

Before printing V3 fan mount please ensure that you don't have bed leveling probe screw mounts on the right hand side of your print head.If you do then please be aware that fan mount will not sit flush hence those screw mounts ar in the way.Also...

Before printing V3 fan mount, make sure you don't have bed leveling probe screw mounts on the right-hand side of your print head. If you do, be aware that the fan mount won't sit flush because those screw mounts are in the way. I'll redesign the fan...

Redesigned easy-print fan duct is now available for the SecKit SK-Go using a BMG clone. The new design sets the height off my hot end, closely matching yours. To balance out the uneven output of the factory fan, I've incorporated offset internal...

This fan duct design is for an Ultimaker and incorporates a 40mm fan. It addresses limitations in other designs by accommodating thicker fans without interfering with the X carriage block during homing. The design features a 360-degree duct around...

Ender 3/5 Fan Duct Pro - featuring an optimized design that reduces the steep overhang to approximately 45 degrees, allowing for smoother printing processes. ... Two versions are available: a standard option with a slightly larger cap situated between...

This fan duct is designed specifically for the MK8 Extruder, enhancing print quality by cooling down extruded materials, particularly beneficial for small prints and those with sharp corners. It prevents layers from curling upwards and provides...

Just my design of a part cooling fan duct for the anet a6. Does not obstruct the view but allows easy access to the hot end. ...Immediately after printing, the fit may be a little tight, but it can still be easily mounted by hand.

A fan duct that spits out the air both from the sides and from the front. The "arms" that ducts air to the sides are made to immitate a flow-optimized design with large curves and an internal rib to guide the air but no CFD analysis has been done to...

The Zaxe Z1+ 3D printer comes with an exhaust fan that is designed to eliminate the harmful gas produced while printing ABS material. However, since I only use PLA material, the fan runs unnecessarily. To enhance the quality of my prints, I removed...

This is my attempt at a Fan Duct that is incredibly easy to print and cools the printed item without cooling the nozzle as it worked. I also added a cross beam Angle in the center to create some direction/turbulence to the air path. It fits on any...

The "arms" that ducts air to the sides are made to immitate a flow-optimized design with large curves and an internal rib to guide the air but no CFD analysis has been done to prove the design. Made to be printed upright with the side where the screw...

Version 4 of this duct fan boasts a more print-friendly underside, featuring a flat surface that remains in contact with the print bed until it reaches a 45-degree angle. This iteration also incorporates 12mm wide arms, rather than the original 10mm...

* make sure you aren't filling the interior of the fan duct before you print. potential upgrades: * id like to make the left and right feet have a corner lip so they hold onto the corner of the carriage. This would prevent the assembly from...

In order to enhance cooling, I installed an extra duct atop the thermal barrier tube. ...Subsequently, I posted a revised design incorporating auxiliary discs.

I can assist you with that, it's mounts two 50x15mm blower fan on the 3D printer to cool printed layers effectively, a current work in progress, the following details relate to print settings. ...Print Settings Rafts Doesn't Matter Supporters Not...

A 3D-printed fan duct is designed specifically for the 4020S computer cooling blower, allowing efficient air circulation within your device. ...This customized accessory ensures optimal performance while providing a cost-effective solution to enhance...

The revised design brings the ducts closer to the print head, potentially reducing plastic usage. I also added air holes to prevent filament overheating and bending issues. ...This upgrade has proven effective in printing without support, with minimal...

The original duct was lower than my nozzle, so I shortened it. ...There are 2 versions, the "flat" one and the 2mm one. The flat one, once installed will be tilted to point down towards the print, the other will be perpendicular to the nozzle.

This is an **experimental fan duct**. ... - No particular use case - Suitable for 3D printing