3d print eurorack

Handy gadget to secure 8mm hex nuts onto 3.5mm Eurorack connectors. ...Files are provided for customization or rebinding.

Vented Eurorack Panels breathe new life into your rack, giving it the ventilation it needs to thrive.

... simple modules when needed. Instructions: 1. Print one side. 2. Print the other side. 3. Print 4 items of the 16HP rails (can be done in the same print). 4. Connect the parts with a 4 mm threaded rod. ...Use a saw to adjust the length of the rod.

This is a smaller Eurorack patch cable holder that can clamp to a desk or shelf. There was a similar design already out there that is wider (https://www.thingiverse.com/thing:3517569), but I needed a less wide version and the geometry was breaking...

This is a smaller Eurorack patch cable holder that can clamp to a desk or shelf. There was a similar design already out there that is wider (https://www.thingiverse.com/thing:3517569), but I needed a less wide version and the geometry was breaking...

... them further, head over to https://www.tinkercad.com/things/aOmWqLj7Q3H . Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: None Supports: None Resolution: 0.2mm Infill: 20% Notes: Printed with a brim enabled for added stability.

The design is mostly complete, so you'll just need to print and assemble. If you're looking for a panel stand, check out my other designs - they have a 2mm gap and lean back by 10 degrees. ...I printed these panels on my PLA printer at 0.2mm resolution.

A 4HP panel for a hand wired passive multiples module for Eurorack modular synthesizer. The jacks are grouped into three. I print this face down on a glass bed to get a smooth finish. ### Materials 3 x 3mm LEDs 3 x 10k resistors 9 x 3.5mm Mono...

... made this about 2.5mm thick which is about as thick as I could go with still allowing the 1/8" jacks I had to fit but it still flexes a bit. It may be better if its printed with something other than PLA possibly. ... 10mm wide x 128.5mm tall ~ 2HP

I Modified the Eurorack Skiff by Adding Imperial Logo Panels Using the 10hp panels designed by Amplivibe, I incorporated the Imperial logo across two of them to replace the row of blank panel covers on my skiff. In addition, I created single 10hp...

This is a 40HP Eurorack panel designed specifically for mounting Korg Volca synthesizers directly into your Eurorack system. To integrate the Volca, remove its case from the PCB, desolder battery and speaker cables, then use four original screws to...

The better means you don't have to buy rails, and can slide M3 nuts in, the worse is you will need to print with supports and those supports are some effort to clean out. I went with the 1300 case because the faceplate can be printed on a Prusa...

...The better means you don't have to buy rails, and can slide M3 nuts in, the worse is you will need to print with supports and those supports are some effort to clean out.I went with the 1300 case because the faceplate can be printed on a Prusa MK3S.

The better means you don't have to buy rails, and can slide M3 nuts in, the worse is you will need to print with supports and those supports are some effort to clean out. I went with the 1300 case because the faceplate can be printed on a Prusa...

Here is an experimental bracket for a Eurorack modular synthesizer, designed to seamlessly integrate with the Parametric Eurorack Rail. Although it works nicely with my own rail system, there are numerous variables to adjust, allowing you to...

eurorack passive multi, made for THONKICONN – 3.5MM JACK SOCKETS. ...u can use superglue or just press it and use the nuts to keap it secure.

Blind cover for Eurorack-Racks. ...2mm thick and in the following sizes: 2HP, 3HP, 4HP, 6HP, 8HP, 10HP, 12HP, 14HP, 16HP, 18HP, 20HP

Expandable Eurorack Module Employs Interchangeable 24-HP Blocks, Easily Upgraded to a Full Case by Replicating and Mounting Additional Units Using Standard M3 Nuts and Bolts.

... generator and Kevin Greenwood's Weave shape generator. Structural stability is achieved through carefully crafted side panels that not only serve their functional purpose but also add to the aesthetic appeal of this unique Eurorack synth design.

... These are designed to fit perfectly with Behringer Eurorack rails, but adjustment to the source file might be needed depending on what type of rails you have. ... This is a work in progress, if you have requests or suggestions please let me know.

Dies ist ein Eurorack-Modul für den Eigenbau-Oszillator von Look Mum No Computer: https://www.lookmumnocomputer.com/cem-3340-diy-simple This is a eurorack module for the Look Mum No Computer DIY Voltage Controlled Oscillator:...

Here is a .SCAD file for creating blank Eurorack panels that requires minimal effort to use; simply specify the desired hp, the total number of mounting holes (top and bottom combined), and an optional hole width parameter (defaulting to 5.08mm) if...

... done carefully, this process is non-destructive, allowing me to potentially return the speaker to its original state. I omitted the mounting holes in my print, as they often lack accuracy, and instead drill them using a Dremel for precise placement.

Users often need a straightforward way to secure their Eurorack jacks, which is exactly what this easy-to-use hex nut tightener delivers. ...It offers a delicate twist that won't damage the module's panel.

This is a simple 4HP eurorack blank panel. It's for keeping fingers (and loose cables!) away from the sensitive insides of a modular synth.  

eurorack rail for 104hp, 3 rails and 2 connectors to make 104 hp, u can use the connectors to hold the rails or screw them to the panel of the case.

A Personalized Module Builder for Eurorack Panels.\r\n\r\nDownload and customize the .scad file to tailor your own custom components, including precision potentiometers, ergonomic switches, and a wide range of additional features.

The Polaron drum machine gets its own dedicated home in this Eurorack case, functioning seamlessly as a standalone unit too. Though not flawless, it still delivers results with a bit of makeshift support on the front side due to the lack of a direct...

... holes for the jacks were widened by 0.2mm to make fitting easier. I use Eurorack as a platform for effects processing on guitar and bass guitars. ...This module functions as a double passive splitter/combiner, handling two signals simultaneously.

Eurorack case (also works as a standalone case) for the Polaron drum machine. It's not perfect, but it works. It benefits from a bit of a shim on the front side because there's nothing affixing the PCB to the front (the back has a screw hole to mount...