3d print deburring tool

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

So _1_6_10_7 is 1:600000000 or one in 60 million. S16 PrometheusPrometheus is a small inner Saturn moon. It orbits near the inward side of the F ring. Its gravitational influence helps to stabilise the ring. This type of moon is called shepherd...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

___________ The whole Space Pirates collection comes pre-supported and has been thoroughly print tested. It was first available on our Patreon channel in April 2021. ...Our Patreon creates different collections of sci-fi miniatures each month -...

&nbsp;After you print 9 pins and rollers you can force a bearing on each end of the rollers, put a dab of super glue in the sunken pin hole and then set the pin through the body and roller to secure it. &nbsp;Rinse and repeat. &nbsp;</p><p>I had to...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

Building Instructions: Assembly: Print all parts first. Put an M3 nut into the opening of the parts called SensorPhotoTransistor and SensorLED. Put these two parts into the water meter main part. Slide rods through holes in the main part and the...

(Print "FrontPanel_input_noSCART" instead of "FrontPanel_input") If you connect Component or VGA, you can use a SCART breakout to pass through audio in a clean way, without ever having to swap the plug on the back. Last, you'll need 8mm M3 hex bolts,...

2) when everything are ready, and the housing was printed out. you can starting to connect the circuitry as per attached diagram. Please make sure the coinnection is correct before you put through the live electric supply. 3) I didn't reserved the...

I did just make them to show how the frame look like. Printer settings:Infill- 36% Grid patternPerimeters- 4Hight- 0,2I needed to use XY compensation +0,2 on my printerHAPPY PRINTING!  You need: 4 props where 2 is CCW and 2 is CW12pcs M3x8mm...

I figured if I ever had a print that needed that additional ~5mm of build volume, then I will deal with new lead screws then. I also already have an Ender 5 Pro with a Dual-Z XL upgrade for a whopping 500mm Z build height, (but still only a 220mm X/Y...

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

Instructions If you plan to print in ABS, scale the object up by one press of the up arrow or the case will be too tight. ... Using the following options: 5width = 58.6 5height = 7.6 iphone_version = 1 4_per radius = .3 pattern_rotation = 10 5cornerR...

Furthermore the PLA which I used to print these funnels is partially water repellent so that frictional effects are small. A Better Turbo Funnel ---------------------------- Bernoulli's Theorem states that the flow rate is proportional to the...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

On my version, I suggest that you start with 4 seeds in each of the 12 pits (print 4 copies of the 12 seed model and then separate them using nail clippers or small scissors). Increase the number of seeds in each pit progressively to increase the...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

The support piece in the D-pad space will punch out with a punch and hammer after printing.Just place the shell on something with free space under the D-pad area and punch the support piece. Wiring the 9-pin d-sub for Amiga, Atari, Kempston or SEGA...

Installation ------------ Print out the four switch holders and slide them into the aluminium channel on the X and Y axis, as shown in the photos. The X axis holders are slightly longer than the Y axis holders. The tolerance is quite tight so they...

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

All parts are printed, including hinge pins. I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to...

electrical conduit pole. Print instructionsWhy I Built It I have an outdoor weather station that has batteries inside the instrument array. Changing the two lithium AA batteries once per year involves getting on the roof which is a PIA, so the idea...

TRABAJO EN PROCESOCon este upgrade convertimos cualquier SIGMA a filamento de 1.75, usa extrusores Titan y Hotend V6 de E3D Original.Hemos respetado todos los componentes originales de la impresora, los ventiladores, el termistor y el cartucho...

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

Printed Parts Assembly Mount pt 1 Assembly Mount pt 2 Backer Plate Bearing Filler 3to5mm X 2 Spur Gear11 Spur Gear21 Switch Plate Hardware Bearing: 5mm ID, 10mm OD, 4mm thick X 2 2.5mm x 14mm Cap Screw X 10 2.5mm x 35mm Cap Screw X 7 2.5mm Nuts X 8...

... post 'em! Really! Take a cameraphone photo with your dope color matched mount in all its glory and show it off! Plus it really helps get this design out there to the world.Want a generic GoPro mount version?I got you covered, check out this design.