3d print death stranding

All parts are printed, including hinge pins. I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to...

Added a photo showing the Endstop in fluorescent green filament. Print Settings Printer: Woodstock Delta Rafts: No Resolution: 0.2mm Infill: 25% Gyroid Filament: Generic PLA, PETG Any Notes: Orientation is often not correct, you will most likely...

... and USB-C charging cables. ### Miscellaneous I printed this in GlowInTheDark Blue PLA which looks very nice at night. ... If you want any other file types for a remix or something else just leave a comment and I'll do my best to provide them.

for both the FGC68, FGC6 and FGC9 in case you don’t want to wait of manual update a already printed shroud just fallow the steps in this video. https://www.youtube.com/watch?v=480iDroe8h0...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...

As for printing requirements, please note that some of the parts in the images do not match their .STL file counterparts due to an error on my part. I uploaded images that demonstrate how to obtain the correct pieces if you encounter any issues. All...

-AUTO TRANSLATE TO ENGLISH- After 3 years of using my mobile charger (huawei P30 PRO) the connector had started to break slightly (surely my cat biting it and dragging on the ground helped) so I decided to print a protector. The regular models were...

There are also two variants of each model - one "basic" variant, and one variant that has been slightly altered to suit printing at 28mm scale. You will find all 28mm variants in the zip archive named "28mm versions" included in the purchase. All...

There will be a lot of soldering, and you'll want to make changes to the CAD and do a few test prints of your own if you want good results. Read further down for more info. === Flaws === Firstly, you should know what you're getting into. To be...

(Plug the cables from battery into the standard +3.3v and GND pin on DevKit board - or solder/mount them someplace different).Shopping Recommendations:LiFePo4 AA BatterySingle AA Battery HolderPrint flat sides down - no supports. This will basically...

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

To achieve the insert as shown, print six of the player trays, two of the resource/silver trays, and one of everything else. The photos show how to layer all the trays, game board, and manuals in the box. ... I have included the original OpenSCAD...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

By any means you are now scared to do this operation, I highly suggest you ask someone with expertise to help you on your endeavors.You have been warned.Step 1: partsFirst you need Noctua nf-f12 for the psu and Noctua NF-A4x10 FLX 12v Version.you...

The two `o_ring` files are optional o-rings you could print with flex filament. Better to use o-rings, and at a pinch you can probably get away with using a rubber band, or just pushing everything together and putting up with water splashing...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

It has a thin bone structure, so I recommend printing it in a large size or on SLA/DLP. Ovis From Wikipedia, the free encyclopedia Jump to navigationJump to search This article is about the genus of wild sheep species. For the domestic animal,...

First, you'll need a 2 gallon bucket (I got one from Home Depot for a few bucks), some M5 screws and some M5 knurled brass threaded inserts (use a soldering iron to install in plastic).I also included a strap mount so I didn't have to carry the ICM...

It all sounds confusing and over complicated but I can assure you that once the pieces are printed most of the process is fairly straightforward and the other parts to be used can be sourced quite economically. Finally, I will recommend a minimum...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

**Please buy using the following links to support my creations (doesn't cost you anything):** [Good quality E3D V6 clone][1] [1]: https://s.click.aliexpress.com/e/_AqHeoo [Good quality E3D V6 clone copper version][2] [2]:...

It doesn't cost you anything extra, but helps me out a lot :) Both links in this post are affiliate links. Print instructionsCategory: Hobby Summary Update: I added a second version of the top part of this case, which has a cut-out for those who...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

It will then print out a message to the console with the planet's name, its description, and its scale. Please note that this is just an example script, and you may need to modify it to fit your specific needs. Additionally, this script assumes that...

Only a few parts are needed and it is easy to print, preferably in PETG.You can mount it in different ways, on a tripod, with a table clamp or simply with screws.I would still have to work a little on the software, but it works so far.The stepper...

Case for Atari 1050 / XF551 floppy power supply unit. Krabička pro napájecí zdroj disketové jednotky Atari 1050 / XF551. Print instructionsenglish text bellow ==== CZ ============ Napájecí zdroj pro floppy Atari 1050 / XF551 Jde o návrh napájecího...

The upper side of the mausoleum structure is covered with a flat roof made of lead. Print Settings Printer Brand: Creality Printer: Ender 3Rafts: Doesn't Matter Supports: NoResolution: 0.1~0.2 Infill: %10~%15 Filament: NA PLA NA Notes: There...

All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use 220x220 - you need literally for a couple of parts to minimize support. Assembly video: 1)...

3X M6 hex nuts - two for EAF adapter and one for TP-Link adapter If you use a William Optics Dual-Sided 210mm or 245mm dovetail plate, use the following bolts: 2X M6x60 SHCS for riser 2X M6x20 SHCS for EAF adapter 1X M4x16 SHCS for ASIair Pro 1X...