3d print bridging

The bottom surface has irregular surface with wholes to make it more difficult to print the bottom layer. There are also bridges and diagonals for benchmarking the printers abilities. The printbed adhesion can be measured by pulling with a...

Designed this bridging and overhang test with an actual bridge as result instead of the boring straight bridging parts you see everywhere. Just for fun because we can! This part is easy to find and share with others, just search for Bruggetje...

Mini benchy for just bridging and overhangs to 90 degree. ...As small as possible.

K3D bridging test. ... 2 versions: - 50 and 100mm - 50, 100 and 150mm

Human: Customized Version of Thingiverse's Project Number 476845 Created with the Customizer Tool Available at http://www.thingiverse.com/apps/customizer/run?thing_id=476845 Instructions Utilizing the Following Options: Bridge Height Set to 0.8 Units...

... Units 4. Define Maximum Bridge Length at 100 Units 5. Determine Minimum Bridge Length at 10 Units 6. Establish Bridge Angle at 18 Degrees 7. Designate Bridge Z Gap at 0.2 Unit 8. Set Bridge Height to 0.8 Unit 9. ...Assign Wall Thickness of 0.6 Units

http://www.thingiverse.com/apps/customizer/run?thing_id=476845 Instructions Using the following options: Bridge Z Gap is set at 0.2 millimeters. Wall Thickness stands at 1 unit. Bridge Width measures 3 units in diameter. Bridge Increment increases by...

http://www.thingiverse.com/apps/customizer/run?thing_id=476845 Instructions Using the following options: Increment bridge gap by five millimeters Set wall thickness to one unit Set minimum bridge length at one unit Set hub diameter at 24 units Adjust...

Increment Bridge Length by 3 Units 3. Maintain a Z Gap of 0.2 Units Between Bridges 4. Establish Wall Thickness at 1 Unit 5. Tilt Bridges at an Angle of 18 Degrees 6. Designate Bridge Width as 3 Units 7. Limit Maximum Bridge Length to 50 Units 8. Set...

http://www.thingiverse.com/apps/customizer/run?thing_id=476845 \n \n \n \n Instructions Using these options:\nAngle of bridges is 18\nGap between bridges is 0.2 inches\nStep of bridge layers is 2\nHeight of bridge layers is 0.8 inches\nMaximum length...

If you want to complete a  bridge faster with minimal affects, I recommend leaving the print speed at 17.5mm/s. So what can we do to accomplish this perfect bridges? I'm going to really try something controversial here. I was just...

Can print one by one or multiple ones sequentially with different temperatures, printing speeds, extrusion speeds, retraction,...etc. Will help with deciding what the best settings for printing with current or new materials. Easy and simple design...

I suggest to try to change this setting in order of importace: 1) retraction mm (from 0.8 to 10) 2) Speed of retraction (20 to 40mm/s) 3) Try to lowering you themperature; 4) Dry your filament; 5) Buy better quality filament; 6) Use z-hop (from...

This is just a straightforward bridging and retracting exercise. ...Please feel free to provide feedback for future refinement.

This is just a simple bridging and retraction test. ...Feel free to leave your critique for future improvement.

http://www.thingiverse.com/apps/customizer/run?thing_id=476845 Instructions Using the following options: Bridge increments increased to five Bridges widened to three units Angled at 18 degrees sharp Set height to 0.8 inches above base Hubs set at...

Customized Version of Thingiverse Design Created with the Customizer Tool at http://www.thingiverse.com/apps/customizer/run?thing_id=476845 Settings and Options Max Bridge Length Set to 100 Units Narrowing the Gap between Bridges to 3 Units in Width...

To build this item, follow these instructions using the following settings: * Set the minimum bridge length to 10. * Set the wall thickness to 1 unit. * Adjust the bridge increment in steps of 5 units. * The bridge width should be set to 3 units. *...

Design Your Dream Model Using the Advanced Customizer Tool Visit Our Website: http://www.thingiverse.com/apps/customizer/run?thing_id=476845 Get Started with This Customized Version of the Original Model **Easy-to-Understand Instructions** With these...

Just a quick test (about 1 hour) for testing the bridging capability of your FDM printer and its settings. Features: -bridge length: from 2cm to 10cm -bridge thickness: 2mm -thin base for better bed adhesion Advance: -you can play around the x,y,z...

I took OverrideStudios design and recreated it in Tinkercad. ... Instead of making a pin using bridging I created this so that it utilized cones with no support needed.

After pondering why Repetier and Marlin G-Code flavors produced vastly superior prints on the Anet A8 when sliced with Cura 3.2.1 compared to RepRap G-Code flavor, I created this small test piece to generate prints that would undoubtedly fail with...

Design Your Bridge Test with Ease Test your bridge with a customized design that you can tailor to suit your needs. You can select from pre-designed parts or use our intuitive customizer to create a unique solution. ...Be aware that the code doesn't...

It includes several features to test for supports, bridging, drooping, and print quality in general. These features include a large chamfer from the build platform, a large fillet from the build platform, a large fillet from the print surface, small...

This test aims to reduce plastic consumption through a straightforward bridging exercise. ...The split variant, currently under development, allows for testing diverse acceleration and speed configurations within the same section.

Customize Your Design to Test Bridging Now! Create Your Own Look with Pre-Rendered Parts or Personalized Elements. ... Remember, Code Does Not Automatically Check for Errors - Keep Values Within Range to Avoid Glitches!

Key Features: - Bridge length: spans from 2cm up to 10cm - Bridge thickness: stands at 2mm - A thin base for improved bed adhesion. ... Tips for Advanced Users: - You can adjust the x,y,z scaling in your slicer to change the model's dimensions and fit...

This will help you compare the results of different printer configurations and part cooling parts used to produce better designs and settings.What to print?The test has been divided into a 10-50% and 60-100% fan speed model with indicators for each...

Instructions Using the following options: hub_diameter is set to 30mm wall_thickness will be adjusted on the fly to fit snugly between supports lengths over 150 are no longer restricted for maximum reach max_bridges_per_model increased from default...

This produces two distinct layers on the bridge at a layer height of 0.1mm.\r\nCustomized from a version found at https://www.thingiverse.com/thing:476845.\r\nGenerated with Customizer! ...Available at...