3d predator model

https://www.printables.com/de/model/172064-phaetus-taichi-mount-and-fanduct-w-dual-5015-fans- ________________________________________________________________________ This is an highly integrated Mount and FanDuct for the upcoming Phaetus TaiChi...

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

... of the Reitec polisher. 24.06.2022 - Updated the Drumgear to be the correct one. Sorry for the confusion. 24.06.2022 - Added alot of exemplarotry images / and Photos and added alot of BOM. 27.06.2022 - added alot of forgotten models. ...Sorry

A hard case for your Eggtracker Mini to use with high power model rockets. Bill of materials: Eggtracker Mini (only tested with rev C3) Turnigy Nano-Tech Plus 300mAh 2s 70C Lipo Pack (hobbyking, amazon, search around and try not to get raped...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Druidic missionary of Renmaeth who heard the tale of the Anshani Empire in Edrador. Wishing to steer them from their industrious ways, Myrion travelled to the far away...

Used PLA, but as mentioned in the comments, PETG is probably a better choice for the gears. Print 3x '19-screwFront01' Print 6x '22-screwBack01' Change the filament color before the last 3-4 layers for part '05-frontHolder02' to see the text (or...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

I can only describe what I did or share my experiences and provide respective models and a SketchUp project concept file (the .skp file) so that you can adapt or improve it for your Stargate. In one of the comments from '5ft Lighted Stargate'...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

Until very recently, I never got around to actually writing any documentation describing this idea or doing any model of this bearing concept. I only toyed with the concept in my mind for a while back then and put it on the back burner until...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 20...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Crawl-back happened to me exactly 2 times in the past year or more of using these reels, but I thought adding this might reduce that risk a bit.I added a model for a Jo-spacer that is useful for some Jobo center cores that don't have that...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

(I have included a model with logo, and one without)Assembly Instructions:Print the box and two clipsInsert bowtie shaped post on clip in to corresponding hole on box, then rotate until the push-clip lines up with the hole.Push the push-clip in to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

If you are interested in trying this let me know and I can upload the STLs.To get a better idea of the idea I have uploaded a few images to help conceptualize the model.Summary:Got a used 2021 Kia Soul EV that had a level 1 charger but no mounting...

... The COMPLETE Sunken Kingdoms I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Tritons are the proud folk of the seas, which ancestors are common to those of the Alfar.

The bearing is model 6000. I would get one that is sealed to keep the saw-dust out. You may need to do some small scaling with your slicer to get the sizes correct. For my printer the bearing easily presses into the Depth stop, and the collar...

However another person created this and the subsequent prusaslicer ini file. however I am not quite knowledgeable enough with gcode and prusaslicer to make the necessary adjustments to it to make it work on the mini (plus I prefer to do it directly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...