3d platypus

Here are the parts (top down): Antenna Head Visor Eyes (2) Teeth Body, upper Body, lower Door Arm segment, shoulder (2) Arm segment, short (10)* Hand (2) Leg segment, hip (2) Leg segment, short (8)* Leg segment, ankle (2) Foot (2) Stand Also...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

I took care of the 2nd issue by 3d printing my own holder for the remote that would fit in a 1-gang wall box and could use a decora wall plate. The plastic button section on the remote is the right width, but is a little bit too short, so the...

I commonly start plants in an Aerogarden and then once the seedling grows a long enough set of roots, I move it into this bin system.Check out my 3D printed Aerogarden pod design here: https://www.thingiverse.com/thing:4560879Check out my video about...

An example of usage of the Dual Axis V bracket could be to provide the reference pivot in a 3D printer fitted with a 1P Z motion system. <b>The claims for the Dual Axis V-Pivot are as follows.</b> i) There will be no clearance between the...

Note: The G code files are set up to print with PETG material. 2) Procure the commercial hardware from the parts list, M3 screws, square nuts, hex nuts, and 4mm OD x 2mm ID Teflon tubing (or re-use the existing buffer tubing). 3) Cut the existing 10...

Unfortunately the M2.5 taps are usually not included in this little set and will need to be bought separately, but if you're doing 3D printed projects with Raspberry Pi, you'll really appreciate having an M2.5 tap - as the screw holes in the...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

There are however, various integrated supports and sacrificial layers that will require cleaning off after printing (refer to the Installation Guide and the Part Preparation section).2.All parts were printed with PETG, 30 to 40% infill with 3...

Now that I do own a 3D printer, I went and created a nice and customizable planting pot to finally make use of that otherwise rather useless down-spout. \o/Since everyone's situation will be different and there does not seem to be a standard when it...

Because of this I figured it would be nice to dig up the old 2D drawings and turn them into a 3D model so you can print your own Fauvet Girel and motorize it with relatively little effort. I also provided parts for a dummy model in case you want to...

What you'll need: 3d printed parts- -Cuff (if your going with the premade attachments download both top cuff and bottom cuff) -Pegs (there should be 4 in one file) -Core -Lever -Dial -Ring -Base -Base connector -Pins (one of the two is specifically...

With a recommended retail price of 39,99 € (available on amazon.de for about 20 €) it is heavily overpriced (the word rip-off comes to mind).As I got my first 3D printer (an Original Prusa MINI+) a week ago I decided to build my own compatible...

Can be easily adjusted to use another bearing or bronze bushing.And yes, all rods must be in line therefore, the setting can be facilitated using a long ruler or any other object with a straight side.Print SettingsPrinter:Zonestar...

Like… very-nearly-the-whole-MK3s-build-plate-big, so don't be surprisedSettings (how I printed mine, at least):Prusa Slate Silver PETG0.4mm nozzle.2 layer height20% infill (resulted in some surface scarring, but it's not visible on mine when in...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

The tube may interfere with the aperture pin ledge of your M42 adapter (it doesn't/shouldn't interfere with my 3D-printed one though) if it has one. Print and use this adapter at your own risk (risks include, but are not limited to, the following:...

... to about 440. Test it and adjust.</p> <p>Enjoy your new geared extruder. The printing quality on this is worth it!!! Print Settings Printer: P3Steel Rafts: Doesn't Matter Supports: Yes Resolution: 0.25mm Infill: 50% Category: 3D Printer Extruders

Once you have done that you can attach the hose guide to the rear of the mount using the 3D printed standoffs and a pair of M3x8 socket head screws for the mount side and a pair of M3x4 socket head screws for the hose guide, the standoffs are self...

If you'd like to back this 3D printed art project, see https://www.kickstarter.com/projects/laird/snowburst-2014 . The project video is <a...

... cannot be triggered due to the length of its lever, else use A position. The remaining steps should be self explanatory. If you use the fence, don't forget to sand and test it thoroughly before use, as described above. Category: 3D Printer Parts

My ultimate goal with this was 3d modeling practice and trying to model this in a way that would give as little post processing as possible. Ultimately, I needed a little sanding and a little bit of CA glue.For printing, the model has been designed...

To aide in designing this part, I also ordered a complete Neo hotend assembly from Amazon so I could 3d model all of the parts. Unfortunately, the back plate is not available to buy, but I was able to download an stl file from another Thingverse...

... the Fine tuning adapter / rod holder. NOTE: Some more of my other designs: https://www.thingiverse.com/leadingedge/designs Best All-round 3D Printable Knife and scissors sharpener with lots of attachments: https://www.thingiverse.com/thing:4135236

The field is confined by a steel “yoke” that forms the bulk of the detector’s 14,000-tonne weight.CMS acts as a giant, high-speed camera, taking 3D “photographs” of particle collisions from all directions up to 40 million times each second. Although...

There are several 3d printed threaded parts. The internal threads should be cleaned out with a 6mm X 1mm tap. If you don't have a tap you may be able to use a 6mm bolt with a groove dremeled into it. I haven't had to use a die to clean up the...

&nbsp;To your health!The Salud CO2 Monitor was designed to inform you of your local air quality in terms of CO2, while also featuring a long battery life and simple no-solder assembly.In addition to the three 3d-printed enclosure parts, you will...

So, 3D print to the rescue. I found a printable full-size Captain America shield on here (Link to thing), but it said "work in progress", so I designed my own. I was especially unhappy with the way the parts were split (21 pieces), and that there...

After sanding, I applied a pretty thin coat of XTC-3D to smooth out any other issues, and then gave it a light sand after it had dried. After that, I applied a coat of sprayable primer so my paint would have a good surface to attach to.</p> <p>With...

You also need skills in 3D printing with PA or another heat resistant material and you need to drill a few holes into the mounting plate according to the printable stencil of this thing. When talking about front and back, the front is the side of...