3d oculus quest 2

I remixed warmans's design to not block the ambient light sensor (so the quest 2 doesn't wake up when you put this cover on). This doesn't touch the lenses so they wont get scratched. ... Print with PLA with the flat side down, no supports needed.

**Quest2_Elite_Strap_AUKEYBattery_Holder.stl** - For Quest 2 Elite Strap Users **Vive_DAS_Quest2_AUKEYBattery_Holder.stl** - For Quest 2 DAS Users I've linked all the parts I used to create the models. ... **Portable Charger 10000mAh AUKEY Smallest USB...

You can sew it if you want a more permanent close but obviously that is invasive - Some strong superglue or similar(to glue the elastic bands on the speaker caps) - 30mm thick elastic band(any sewing store should carry this, 1m should be more than...

Remove from the Oculus and remove the head cusion etc 2. Remove the 4 screws on the very back 3. Use a spudger or similar under the round 'button like' white part to release the toothed strap sections (they just need levering out) Do not try and...

This is a remix of sekazi's Vive DAS adapter (6.85mm center) (https://www.thingiverse.com/thing:4626882) and tanvach's Quest 2 Strap Adapter (https://www.thingiverse.com/thing:4626664). I really liked the design of sekazi's DAS adapter but noticed...

A alternative Powerbank holder for the quest 2 default strap for longer gaming time and better weight distribution on the head :) Just print it upside like in the screenshot with a small support on the two clips. ...You can easely clip the battery on...

A alternative Powerbank holder for the quest 2 default strap for longer gaming time and better weight distribution on the head :)Just print it upside like in the screenshot with a small support on the two clips.You can easely clip the battery on the...

The handles are suitable for Quest 2 and Rift S. To print the full model you need to print: 3xTrzon 165mm z szyną RIS.stl 1xR Grip Po Lifcie.stl 1x L Grip Po Lifcie.stl 1x Kolba.stl Screw 2 bolts into each RIS rails for reinforcement. Use screws...

A Quest 2 powerbank mount. Adds 6 hours of battery life and balances out the headset to relieve face pressure too! Designed for a Xiaomi Slim Pro 3 10000mAh powerbank, which supports passthrough charging, so it never needs to be disconnected. ...

update: without padding this was actually hurting my head and one of my glued seams popped.quest was def holding to my head better though. I realized later that i had been using the q2 strap way too tight. So the pain and breaking may had more to do...

A alternative Powerbank holder for the quest 2 default strap for longer gaming time and better weight distribution on the head :) Just print it upside like in the screenshot with a small support on the two clips. ... You can easely clip the battery on...

Check https://www.thingiverse.com/thing:4883491 for newer models.** This is a remix of Sanlaki's Quest 2 F8 ping pong paddle / racket / adapter. In Eleven Table Tennis, you can use the "paddle position" of the "Sanlaki adapter" preset, since the...

... Hope it works! (I don't even own a Quest myself, i did it for a friend that asked if it would be possible and decided to share. ...He still haven't printed the model, but as soon as he does, i'll try to fix any major problems and update it here)

You will need a short (~1') USB-C cord from your battery to the Quest charging port. Using this lets you use a power bank larger than the BoboVR battery (5200mah), and may let you charge the battery and the headset simultaneously, if it allows...

Maybe there are tolerances in manufacturing, but the holders from the original design always snapped of my headstrap when putting the quest over my head. ... Caps for the headphone attachments are these: ...

Made this for a very specific battery I bought for the quest which compliments it very well. This holder acts as a counter balance and should extend play time for a few hours. This model fits the standard head strap, and there is a 2nd model for...

Add 4 dove tails instead of 2 to prevent it from deviating from the front of the case.

... be not fit. This model requires a 1.5m hook-and-loop fastener. You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. The battery must be mounted upwards just like the picture. ...

Remixed from this wonderful model here: https://www.thingiverse.com/thing:4742708 Things changed in this remix: -Split the model so it prints in 2 halves without supports -Added 1/2 dove tails to the split but they are too small. Didnt matter at...

2.This adapter can be used for both shakehand style and penhold style without causing tracking problem. You have enough space to put your fingers for penhold. The only extra you need is a pair of M4 bolt and nut. 3.However, this is my first time...

I also didn't bother to add the cable channel since I don't find it very useful. You should use the end caps from the original model. Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Resolution: .2 Infill: 20...

The other 2 files, are from the Sanliki set, but with the left adapter separated from the "Right Dominant" set. You won't need to print those, if you do the rest of the original set. I believe Sanliki made a compact design too, but it uses longer...

The other 2 files, are from the Sanliki set, but with the left adapter separated from the "Right Dominant" set. You won't need to print those, if you do the rest of the original set. I believe Sanliki made a compact design too, but it uses...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Cut off the bottom part like in the photo since it was proving very diffcult to print with it as its a very narrow part

Fits the right hand controller to support it to your shoulder for more precise aiming. Tips are appreciated! ... thank you so much.

Just removed 1.5 mm from the centre of the STL I printed in PLA but will print another in PETG for the durability and flex.

<p>This is a great design, but it had really flimsy attachment points for Koss headphone elements. I broke at least five in the process of building a set for myself and a friend, printed in PLA+ and PETG, tried different print settings but there just...

A battery holder for the EAFU Portable Charger, Compact 10000mAh as found on amazon for only $10-15 usually. Its cool to see a number percentage left on your battery. It's a little tight the first time you slide it in but it gets looser later. It...

Printed without supports 30% infill is probably overkill printed at 100% scale it is fairly loose on the mount (cable tie added some resistance) can be used also just to add some weight to the back of the headset i wasn't sure how much...