3d oculus quest 2

remix grip from https://www.thingiverse.com/thing:4651978 608 2RS bearing * 2 20mm magnet rubber band M3 bolt nuts

Its a remix only bc I added 2 screw holes to the headset part, other than that credit goes to the OP. Thanks Headset didnt need support but the controllers did. I used tree, everywhere. ...

This model requires a 1.5m hook-and-loop fastener. ... You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. ... The battery must be mounted upwards.

... is a Minimal Print. ...intended to save filament Designed for both Headset and Controllers Required materials: 8 screws Notes: -You will need to print of 4 of these, 2 for the headset 1 for each controller -Print on its side to ensure maximum strength

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

UDATE 2: Re-Meshed the wings “conector” in blender, the V2 was made measuring the physical model, while this V3 is made by using the virtual model, allowing for a perfect fit with the base, they both work equally well, but it might be easier to align...

I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original Blank: ...

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

Composite version: Parts: 3d printed components long thin-walled 3/4" tube many short m2 screws 4-6 m3 screws + nuts 4 m4 screws + nuts 100% printable version: Assembly: Insert tube pieces into each other and push in the flexnails, adhesive/acetone...

I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original Blank:...

... ... UPDATE: As Promised, This is a link to the new Braced Headset Holder for heavier Headsets: https://www.thingiverse.com/thing:5727804 Sorry, but the file may have a few artifacts... I'm using Microsoft 3D Builder, So "It is what it is".

3D-printable models for article "An open-source Olfactory Display to add the sense of smell to the Metaverse" in Journal of Computing and Information Science in Engineering. If you use this in your academic work, please cite as: > Lukasiewicz,...

... the top of the VR. Then glued the piece in place. lastly, a 3d pen was used to make a perfect seal, as well as a bit of low poly foam. You will likely have to trim the part a bit, it was made without knowing the exact headset curve... ...

There is a recess within butt to conceal the knot. There is a hole in the butt that will fit a quick release sling swivel. Support free printable parts Print left or right handed controller clamps Print 3 clamp nuts Print one of each of the remaining...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi, but the adapter is movable, so I decided to make it 2mm longer and added a small clip at the end, so it does not get off...

This 3-file OpenSCAD project is a remix of the excellent "Oculus Quest Magnetic Prescription Lens Adapter" project by jegstad: https://www.thingiverse.com/thing:3659124/ Two of the three included files are unmodified from the version V2 of that...

Protective/decorative covers for your Oculus Quest 2 controllers! The holes allow proper tracking of the IR LEDs. Designed to be printed in TPU and slipped directly onto the controller. Three versions: (1) Original - Minimal with small holes. I...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi (https://www.thingiverse.com/thing:4624192), but the adapter is movable, so I decided to make it 2mm longer and added a...

These 3D models are very accurate and you can use them to make accessories for the Oculus/Meta Quest 3, print them, or do whatever you want with them.If you would like 3D models to use to make accessories for the Oculus/Meta Quest 2 headset I have 3D...

The Oculus Quest VR Headset is a high-quality, intricately modeled 3D object. Originally created using 3Ds Max 2017 and rendered with V-Ray 3.50.04, it was later converted to 3Ds Max 2012 for rendering with V-Ray 2.00.03. The model is available in...

Oculus Quest VR Headset and Controllers were initially modeled in 3Ds Max 2017 before being converted for rendering with V-Ray 3.50.04 and V-Ray 2.00.03, respectively, in 3Ds Max 2012. Available formats include Max 2017 (with MeshSmooth), Max 2012,...

Here's a detailed 3D model optimized for low-poly rendering, perfect for seamless integration into your game engine. ...Each texture is meticulously crafted using Physically-Based Rendering (PBR) techniques to ensure realistic lighting and reflections...

The detailed, fully-textured 3D model is optimally rendered up to a 2K resolution, created using 3ds Max 2012 with V-Ray. It features clean topology, real-world scale and proper naming/organization. Various file formats are supported including Max,...

Just my design of a Anker Powercore 2 10 000mah holder for Oculus Quest 2 (for elite and basic strap) The locking of the battery is done with a cable tie

https://youtu.be/3c4S7vyELSE for oculus quest 2

This is a quick IPD checker I made for the Oculus Quest 2. Very handy for when you want people to try out VR without needing a ruler to check their IPD The way to use it is by lining up the left point with one eye, and seeing which point their other...

Oculus Quest 2 Strap mount with battery v2 PLA or PETG

Two-Handed Sword Adapter for Oculus Quest 2. ...Feel free to remix and improve

Holder for Oculus Quest 2 controller holder and plate to stick it to the back of your hand.

This is kind of a remake from https://www.thingiverse.com/thing:4761076 because the controller hooks failed to print.. So I remade the platform with stronger and printable hooks(supports still needed) I have included the platform in SKP (Sketchup)...