3d models for vrchat

This spotlight can even be used on .50 caliber guns for military applications due to its high vibration resistance and extreme durability. ...The CML-4 also features a vertical handle in the rear of the unit to make repositioning and aiming this...

As the lights dim and the room grows quiet, the Playmobil world remains, waiting patiently for the next adventure to begin. ...The toys, now still and silent, hold within them the power to transport us back to a realm of endless possibility, where the...

I didn't know what to make of it all, but I couldn't help but feel a sense of admiration for him. Here was this man who had been through hell and back, and yet he still managed to come out on top. He was a true survivor, and I found myself wanting...

For upright standing i used the part Clock_stand.stl from original project at https://www.thingiverse.com/thing:5492067. To attach this part i added a small component. This component is attached to the back body with two screws. Additionally i placed...

It is configured to use the second Extruder port/driver for the secondary Y axis motor in config_adv.h. Extruders and heatbed have been disabled, and mintemp has been decreased to -50 on both to counteract mintemp errors in host software. Here's the...

The ninja's affinity for this particular blade is clear; it's as if they've become one with the instrument of their craft. Their fingers dance across the hilt with an ease that belies the deadliness that lies within. With each movement, the dagger...

And I blame Oleg for convincing me to do it. It's a perfect way to waste half a gigabyte of memory and the decent processing power of a Raspberry Pi Zero W on the incredibly simple task of pressing a button. Since the Raspberry Pi Zero W is...

Nearby, there used to be (today they are not visible any more) three little wells covered by perforated tuff slabs, which provided the holy water needed for the sacrifices.Several steles were found inside the peribolos wall, most of which represent...

If you have m8 tap at hand use that to the side hole for the lock bolt. If not, like me (sure i had it somewhere lying around) just patiently screw and unscrew the bolt a bit first. When a bit of thread has formed warm the bolt a bit with a torch...

The assembly instructions and the print files can be found here http://www.printables.com//prints/293910-educational-clock while for the programmatic part the hardware and the Arduino file you can read here http: //www.printables. com / prints /...

Infill % / support / type of brim i used / type of ironing the part is listed below, including estimated print time for each part Sys 2 t-loc Cyclone Base part#1 ABS 40% infill_in+out Brim 0.2 mm layer + iron 0.2 + Support 19h.30min Sys 2 t-loc...

There he learnt of a Necromancer named Thomas Bazaar who had been exiled from each one of the Draksborne Empire’s magic schools for his practice of Dark Arts, and adopted the moniker of Tyrin Thirazar to study after his expulsions. It was said he had...

Unlike the north frieze, which features a variety of poses, garments, and movements, this side shows riders moving in a straight line with their heads held high, except for one exception on block V, rider (13). The trimmed manes of the horses reflect...

All this suggests that the figure of the dancer was destined for a niche. "The Budapest Dancer" owes its fame to being one of the best examples of the so-called closed, centripetal composition of early Hellenistic sculpture. One of the most...

Those who excel in this field are adept at analyzing complex problems, identifying opportunities for improvement, and implementing effective solutions. By prioritizing human resources management, organizations can reap numerous benefits, including...

There is an official long-working-distance 6x SLWD objective from Vision Engineering meant for rework, but it's very expensive, so I decided to try making one myself with various optics I had laying around. Previously, I created a set of objectives...

This mod is not compatible with the X5SA-500 because it has different motors.Materials neededFor this project you'll need:1x GT2 Idler pulley2x GT2 belt pulley (as shown in the photos below)1x GT2 1220mm Belt (or shorter one if you try this with the...

Note that I usually solder on plugs and sockets, but the LED dimmer module has some screw terminal ones, again from ebay, just search for 12V CCTV plugs and sockets. A "wall wart" like shown will drive fans and a few LEDs, but I've got a lot more...

Control Surface for Millumin, OBS and other streaming Software. Yuo can control 9+2 video/media imputs and 3 audio fonts. Material you need: Arduino Uno Board 11 resistor 10K 11 Momentary push Buttons 3 potentiometer 10K Also you need to install in...

The other has slots at the tail end of the rocket for the fins. I recommend printing a couple of extra fins in case they shear off when the rocket lands on a hard surface. I filled mine as much as half full of water, and was able to get about six...

Supports are only needed for the part cooling duct. I'm not sure about the part cooling duct. I don't know if it is very effective yet. Instructions: 1. Print all 3 parts. 2. Assemble the "Wing" to the "X Carriage" with (2) M5x12mm screws...

Or change the filament in the slicer for each layer - if you don't have a dual extruder ;-). My plan was to print the whole thing multicolor with a filament change. In the end you can find a Youtube video of a boy, which helped me a lot with the...

7.the left linear guide has a slot for a cable tie to hold the bed cable, it also has a hole to anchor an optional cable guide. 8.to level the bed correctly. with the printer on we take the printer to home Z and tighten a little the first screw of...

The text appears to be a set of rules for a tabletop strategy game, specifically one that involves miniatures and dice rolling. Here's a summary of the key points: **Gameplay** * The game is turn-based, with each player taking individual turns. *...

Check for stringing too. If all good, move on to assembling the 2 half bodies together by tightening the 3 screws. Don't tighten in too much or you'll strip the thread. Check again that the axle is moving freely by inserting a piece of filament and...

Therefore the shape of this speaker is just for fun or scientific flavor. The air volume of this speaker is too small to suppress Q value (mathematical index of resonance quality), so I used aperiodic vent (resistive port) design. The space between...

Where to watch Sister Wives Season 14 Episode 3 online for free full streaming access. CW || HBO || Adventure and comedy || 55 minutes. #===========================# WATCH FULL SERIES HERE: https://bitly.com/2Mkmnj6 WATCH FULL SERIES HERE:...

...  -On the top of your welding hood: drill screw holes for M4 bolts and one large 20mm hole in the middle of them to mount blower. Bed the blower body down with a little RTV to prevent leaks. Hook up batteries and plop them in your shirt pocket.

If printed standing upright, there's no need for supports. There are two USB covers: one with letters and one without: either should print fine without supports. 2. Clean the bottom of the printed parts with alcohol, and clean the areas on the...

This is a case for the ZB2L3 Battery Capacity Meter / Tester. Please note that I made several modifications to my device. You can't use this case without unsoldering the buttons, screen, and LEDs - it's not hard and definitely worth it! The...