3d modeling on ipad

I imagine they'd be suitable for most medium sized parrots but cannot say for certain; let me know how your bird gets on. This multicoloured print is achieved by pausing and swapping filaments mid-print. <a...

On March 17, 1441, during the reign of King Sejong, he rode a carriage pulled by horses for the first time at Gama-gol (加麞谷) while visiting the hot springs in Onsu County. The cart was actually a distance-measuring device called the kilogoche...

So I needed a method of holding a longshanked hex nut driver in a stub handle, to be able to get under the printhead of my original Prusa i3 MK3 and be able to remove & change the nozzle on the hotend - without having to go out and buy a (costly!)...

All components are available on my website for sale at really good prices; the link is in the description below. https://youtu.be/SPpgMl_TeIc Step 1: Hardware Requirements For this project, we need: - A 5v Solar Cell (make sure it's 5v and not...

Parts needed: 10mm x 15mm ON/OFF switch...

Note: I added an additional tab w/ holes on the left side for extra security. You'll just need to drill and tap the holes in the saw. I also add a piece of a silicone mat to this for extra dust collection. • GMC Dust Port - This is an adapter to...

Since it is underslung and not reinforced in any way, because I am absolutely terrible at even kid level Tinkercad, I'd suggest not hanging one of the big FT5 original steppers (5kg/cm) on it, since that may have lots of Y-vibration and you will...

I didn't put a lid or duct on the fan, because I have bad experiences with make axial fans "stall" while blocking their air too much. I rather will open up the cover once a year to get out the dirt, instead. For wireing information, please look at...

It may be possible to print them vertically so that you can put more than one piece on the bed at a time. If I redo it, it will be designed to print vertically. This case moves the controller outside the case, allowing better cooling. The plexiglass...

Here is the text without any extraneous characters: Instructions Using the following options: lug_width = 5 font_name = Alice lug_style = pointy glyph_coalesce = 25 border_width = 1.5 outlineextruder = extruder1 font_with_style = textextruder =...

That same technique could be used to mark the vertical angle on a side of the body. Once I revealed the film I noticed some light leaking. In addition to the glue you should use to join all the pieces (except for parts 1, 2, 5 and 7), and despite I...

There are currently a total of 4 files: The camera stand base This is the main piece that sits on top of the pole lamp. It slides down over the pole and onto the top screw/nipple. There is a hex hole at the top to accommodate an M10-1.00 nut...

The four M3x5 screws that come on the CR-10S Pro are not long enough to mount the bottom brackets. I found M3x8 screws with washers are needed. You will need to get the two Left & Right Frame Top 10mm STL files from [Anar's...

If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link: https://www.tinkercad.com/things/8S3oiDKDSwc Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

--------------------- In order to maintain my original build height on my [horizontal X axis conversion](https://www.thingiverse.com/thing:3201330), I had a few options. * Increase the bed height relative to the Z assembly, which could cause...

... idea for this project comes from <a href="https://www.prusaprinters.org/prints/39453-prusa-mini-led-light-bar">jagr200</a>. Its design did not fit so well on my Mini. ...I then completely redesigned it from scratch and optimized some details.</p>

Note 1: The retaining clip or 'bump' on the Cam V2 Holder will lose some of its memory over time, but the reduced force should still be sufficient to steady the unit and offer sufficient resistance to prevent it from popping out when the switch is...

you see on of the first Versions in my picture, i did stiffen up the mounting plate, so normally the tape should be needed, but still i would like to add some mount back to the bltouch hold but not done yet... This is my Single 4020 Fan...

Check out this YouTube video to see it in action: https://youtu.be/1u6cYjKVWMs If you are interested in even wider curbs, I'm also making a 57 mm wide version: https://www.thingiverse.com/thing:5821299 **Straights** - S100: For 100 mm straights -...

Overall, the support has a lean style, a bit “naked” so no coverage but sweet on the curves, trying as always to enhance the aesthetic side as well. As with other kits, this one is divided into several parts to make it easier to mold and come out...

These inserts are printed on adhesive material. The bottom insert is cut at a width of 20cm with a height cuts at 25cm, 15cm, 13.5cm and 3.5cm creating 10cm x 20cm inserts. Changing and creating SCAD files CrystalSCAD and OpenSCAD were used to...

If you want to recreate this you'll need the following things: -transparent filament for WARZONE logo -black (or colour you want) filament for the lamp case -on/off snap in switch...

Rolen fled, nothing but his master’s weapon and the clothes on his back with him. After months of wondering and completing odd jobs throughout Tharador’s nations, he signed a contract with the Golden Griffins, for he spotted Ash of Goltia – the...

... League. Without hesitation Orlena loosed an arrow between her superiors eyes, gathering evidence of their betrayal and presenting it to the other councilors, earning her promotion to Master of The Poisoned Talons herself and a seat on the council.

So in all moments of hatred Ash would be led on like this. Eventually the curse was broken by champions of Erdrydion who visited the ruined city and restored the rivers and Ash’s humanity with a holy ritual. Hinatal free once more it slowly regained...

... That prints the nicest looking stream and can be done on printers with bed sizes as small as 150mm x 150mm. When assembling, try the different trapezoid shaped pin sizes and choose the largest one that inserts into both the splash and the stream.

It is very comfortable to have 2 Coin Organizers that can be placed on 2 sides of the table, especially if you have more players. BADGE&BANNER HOLDER: One Badge&Banner Organizer is sufficient for all SW Badges and Race Banners. If you have SWU, you...

The stock skids on your QAV-R 2 are probably just fine for casual flying, but if you're pushing your quadcopter to its limits or flying in rough terrain, they might not be enough. That's where these easy-to-make skid mods come in – they'll give your...

The other 2 packs are here: https://www.thingiverse.com/thing:4120637 - Sector Mechanicus Wall Link https://www.thingiverse.com/thing:4231310 - Sector Mechanicus Wall Link 2 If you like my work please consider supporting me on Patreon. Become a...

________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad link: Will be added later ________________________ Some of my other designs:...