3d model tree

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 30 stencil_pattern_element_shape = 3...

... - The +1mm fan duct is for use with longer non-standard m6 nozzles - Use the following commands to use with stock Prusa firmware: M92 E690, M500 - You may need to adjust the extruder motor current using M907 but that depends on your motor model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

A simple to assemble version of the ER11A Z axis probe that screws onto an ER11A spindle. It has indicator LEDs and can be used to measure and compensate for a bed that isn't flat when engraving, for example a PCB or a curved surface. I use it for my...

It is intended to be loosely attached, for quick removal during total eclipse photography, and as a result, may not remain well attached in a windy or gusty environment.Materials neededPLA or another rigid filament for the frame pieces.Flexible...

... - Schematics:  Goggly eyes are optional, but they improve performance and friendliness of the finished project. Modelled using tinkercad & blender. ...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them). Printing and InstallationAll parts can be printed...

UPDATE: 07/16/2019 Project 399 - Front Crossfire Mount - Depressed 3525.stl - I've been running this model the most. I thickened the sides so it provides more lateral stability, improved the chamfer at the sides to make it smoother, and I thickened...

I made a small update to it, adding the model with the included screw threads in the back, and ever since that update the thing is still there but returns a 404 error for everyone who isn't me. I've tried to get it to post, I contacted thingiverse...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

* The Ridgid adapter / switch part that you previously had to purchase separately is no longer needed, it is modeled in. You use more of the same brass strip used for the Ryobi part to create the Ridgid battery contacts. * The clips for the Ryobi...

Eye diameter - These three dimensions make up the foundation of this model's unique structure, resulting in eyes that stand out at an impressive six units large. Layer height - Perfect for intricate designs or subtle layering, with a precise setting...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 19 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_extra_port_y_position = 30 custom_back_camera_x_position =...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

- The barrel at the front stabilizes the cars but is limited in size, preventing some models from fitting inside. However, a vast majority should fit without issue. PRINTING: - I print the main body and shaft separately from each other, as well as...

3 perimeters 7 bottom layers on the cap ( definitely overkill ) 4 top layers Gyroid fill pattern ( any pattern will do ) Extra perimeters if needed was checked Seam position Rear ( make sure the hinge potion of the model is pointing towards the back...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

What's IncludedThe entire Anvil Digital Forge Patreon release for January 2024, including; Multi-Shell Options:A number of STLs are labled with "(Multi Shell)" - these files can be imported into Blender (reccomended), or Meshmixer, or various other...

and using less material) The idea is to print the markers in a different colour using the "Filament change" script (under Cura, M600 gcode, if supporter on your printer); you may also use the standard rotor-cover.stl if not interested by this version...

If you do this, use the "Pusher Extd" model. To modify the solenoid: 1. Remove plunger. Remove about 3mm of the black base and sand flush with the metal slug. Sand the black base to make it slightly thinner if you want to add an additional spring...

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

If you are interested in trying this let me know and I can upload the STLs.To get a better idea of the idea I have uploaded a few images to help conceptualize the model.Summary:Got a used 2021 Kia Soul EV that had a level 1 charger but no mounting...

My Fusion 360 CAD model has 0.09mm of axial clearance so the printed threads should effortlessly spin together. Extruding over 0.09mm will make it extremely difficult to twist the nut and bolt together using fingers, so just reprint both parts with...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.