3d model spiderman

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

This is a well known test model with many remixes.However, I have not seen anyone with automatic temp range.Existing temp tower is “semi-automatic”, they set temperature to preset levels with custom g-code in “before layer change”This print set...

Print Settings Printer: Heavily modded Craftbot Rafts: No Supports: Yes Resolution: 0,15 or 0,20 mm Infill: 33 or 50 % Notes: Print both models in PETG with 3 mm thick walls and slightly hotter than usual, this should give you enough strength for a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

ANYCUBIC Photon Mono X Clip On Heater Mount PLEASE READ EVERYTHING 01/24/2022 - Fixed the length on the right side of the clip part, opposite to the heater, closest to the rails (it was too long and wasn't aesthetic) 01/22/2022 - Evidently there was...

I RECOMMEND THIS ONE INSTEAD:https://www.printables.com/model/169138-prusa-mini-detachable-cooling-duct-assembly-v2 About this modI have never been happy (okay that's a lie, I was happy for the first few weeks) with my Prusa Mini's cooling. This is...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

You can find the newer version here: Phone Mount for Van Moof S2/S3 V2.0==================================================================== Rotating Phone Mount for the Van Moof S2/S3 electric bike.Mounts to the handlebar using 3 cable-ties,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

 For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base.  The adhesive mount’s socket is smaller...

... The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 34 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

This allows the flow rate to be tweaked only for the detailed layers [as described here](https://support.ultimaker.com/hc/en-us/articles/360013370140-How-to-adjust-print-settings-of-a-part-of-my-model-in-Ultimaker-Cura). Update 4/10/2022 (v4.2):...

This is a stepper motor-controlled model turntable designed for 009 but compatible with short N gauge locos (loose the fences). The bed is 100mm long, and the Arduino code will follow in the coming weeks. Primarily designed for DCC++ JMRI CMRI...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Also download the original 'COMPLETE.BLEND' from Jumpman971's Thingiverse so you can see the model in Blender. (Also get Blender.) (I'm pushing this out before a throat piece is remodeled because I have a 2-week vacation coming up and I'm busy this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

# Anet AM8 motherboard case This case is inspired by a [YZ Case for Prusa made by Carter](https://www.printables.com/pl/model/1910-yz-case). This case is prepared for mount on the Anet AM8 modification frame. It can hold Anet A8 v1.7 motherboard...

I found red, yellow, and pink lights worked the best with incandescent lights and blue or green appear better on LED lights, in my small sample size. To setup the image to be compatible with this clip: Photoshop/Gimp/other photo editor: Crop photo...

I downloaded and printed two of the Flugzeug Halter - Breit STLs in the Model Plane Ceiling Hooks thing from dschiedsch. They worked but were a tight fit for some planes when I tried them out. That is when I decided to make something adjustable to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

also know with ESC if you turn power off with pot turned to high you have to turn the pot down to be able to start motor again (must be a ESC safety thing) Machine drilling a board the failed to drill completely through on the CNC PCB Mill ( My fault...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

- Replaced PZ20 circuit's LDO with a simpler model with higher input voltage range - Added second LDO for dedicated supply to LED's - Isolated TH1 from ground plane to address vdroop effecting thermal readings - Added grounding vias for edges and...